NXR-810
7
REALIGNMENT /
模式组合
4. Firmware Programming Mode
4-1. Preface
The NXR-810 uses fl ash memory to allow it to be easily
upgraded when new features are released in the future.
4-2. Connection Procedure
Connect the NXR-810 to the personal computer using the
interface cable (KPG-46/46A) and USB adapter (KCT-53U:
when the interface cable is KPG-46A, the KCT-53U can be
used.). (Connection is the same as in the PC Mode.)
Note:
You can only program firmware from the 8-pin micro-
phone connector on the front panel. Using the 25-pin logic
interface on the rear panel will not work.
4-3. Programming
1. Start up the firmware programming software (Fpro.exe
(ver. 4.1 or later)). The Fpro.exe exists in the KPG-129D(C)
installed folder.
2. Set the communications speed (normally, 115200 bps)
and communications port in the confi guration item.
3. Set the fi rmware to be updated by File name item.
4. Turn the NXR-810 power ON with the [PF1] key held
down. Then, “P.G.” is displayed.
5. Check the connection between the NXR-810 and the per-
sonal computer, and make sure that the NXR-810 is in the
Program mode.
6. Press “write” button in the window. When the NXR-810
starts to receive data.
7. If writing ends successfully, the TX LED on the NXR-810
lights.
8. If you want to continue programming other NXR-810s,
repeat steps 4 to 7.
Note:
This mode cannot be entered if the Firmware Program-
ming mode is set to Disable in the Programming soft-
ware.
4-4. Function
If you press the [PF6] key while “P.G.” is displayed, the
display changes to “P G” to indicate that the write speed
is low speed (38400 bps). If you press the [PF6] key again
while “P G” is displayed, the display changes to “P G.” to
indicate that the write speed is medium speed (57600 bps).
If you press the [PF6] key again while “P G.” is displayed,
the display changes to “P.G.” to indicate that the write
speed is high speed (115200 bps).
Note:
Normally, write in the high-speed mode.
4. 固件编程模式
4-1. 前言
NXR-810 使用闪存，以便于在将来发布新功能时进行升级。
4-2. 连接操作
用接口电缆 (KPG-46/46A) 和 USB 适配器 (KCT-53U: 接口电
缆为 KPG-46A 时，可以使用 KCT-53U。) 将 NXR-810 连接到个
人电脑。( 连接方式与 PC 模式下相同。)
注意 ：
您只能通过前面板的 8 针麦克风连接器对固件进行编程。
使用后面板的 25 针逻辑接口进行编程时不起作用。
4-3. 编程
1. 启动固件编程软件 ( F p r o . e x e ( v e r .4.1 或更高版本 ) )。
Fpro.exe 存在于 KPG-129D(C) 安装文件夹内。
2. 在配置项中设置通信速度 ( 通常为 115200 b p s ) 和通信端
口。
3. 通过文件名项设置要更新的固件。
4. 按住 [PF1] 键打开 NXR-810 的电源。此时 , 显示“P.G.”
。
5. 检查 N X R -810 与个人电脑之间的连接，确认 N X R -810 处于
编程模式。
6. 按窗口中的写入按钮。NXR-810 开始接收数据。
7. 如果成功完成写入，NXR-810 上的 TX LED 亮起。
8. 若要继续为其他 NXR-810 编程，请重复步骤 4 到 7。
注意 :
如果编程软件的固件编程模式设为禁用，则无法进入此模
式。
4-4. 功能
如果在显示“P.G.”时按 [PF6] 键，则显示变为“P
G”以
表示写入速度为低速 (38400 bps)。如果在显示“P
G”时再次
按 [PF6] 键，
则显示变为“P
G.”以表示写入速度为中速 (57600
bps)。如果在显示
“P
G.”
时再次按 [PF6] 键，
则显示变为
“P.G.”
以表示写入速度为高速 (115200 bps)。
注意 ：
通常以高速模式写入。
