![Kenwood NEXEDGE NXR-810 Скачать руководство пользователя страница 18](http://html.mh-extra.com/html/kenwood/nexedge-nxr-810/nexedge-nxr-810_service-manual_192292018.webp)
NXR-810
18
10MHz or
19.2MHz
Detector
RX VCO
/PLL
3dB
ATT
3dB
ATT
X58-5090-10
2nd Lo
REF
AMP
Q504
AMP
Q502
AGC AMP
Q503
Buffer
Q501
SW
X3
Q202
LPF
LPF
CN500
LPF
D503
AMP
IC500(B/2)
AMP
IC500(A/2)
X500
OSC
19.2MHz
D504,D505
EXT_IN
10MHz
Fig. 1 Internal/external reference circuit /
图 1 内部 / 外部基准电路
2-2. Transmitter reference 16.8MHz PLL circuit
The transmitter reference 16.8MHz PLL circuit produces
the reference frequency signal for the Transmitter Main PLL
circuit and modulates the low-frequency components.
The circuit consists of IC600, IC601, IC602, IC603, IC604,
Q601, Q602, Q603, and X600.
The VCXO (X600) signal enters the buffer amplifi er Q603
and is amplifi ed by Q602. The higher harmonic wave is at-
tenuated by the LPF and returns to IC602. Its phase is com-
pared with that of the reference frequency 5kHz.
The phase difference signal produced by the comparing
phase is converted to a DC voltage by a lag-lead type loop
fi lter. This DC voltage is input to the IC604 invert amplifi er
and is synthesized with the modulating signal. This DC volt-
age is input to the X600 control voltage terminal for control-
ling the VCXO oscillating frequency 16.8MHz.
The 16.8MHz oscillating signal is fed to the Q603 buffer
amplifi er. The output signal of the buffer amplifi er is used as
the reference frequency signal of the transmitter main PLL
circuit.
TX VCO
/PLL
MOD
PLL IC
X58-5100-10
Ref
10MHz
or 19.2MHz
LDT
IC602
SPSCLK0
SPSD0
/16_8PCS
AMP
Q602
Buffer
Q603
AMP
IC604
AMP
IC603
16.8MHz
LPF
Loop filter
X600
MB
OSC
16.8MHz
Fig. 2 Transmitter reference 16.8MHz PLL circuit /
图 2 发射机基准 16.8MHz PLL 电路
CIRCUIT DESCRIPTION /
电路说明
2-2. 发射机基准 16.8MHz PLL 电路
发射机基准 16.8MHz PLL 电路产生发射机主 PLL 电路的基
准频率信号,并调制低频分量。
该 电 路 由 I C600、I C601、I C602、I C603、I C604、Q601、
Q602、Q603 和 X600 组成。
V C X O ( X600) 信号进入缓冲放大器 Q603,由 Q602 放大。较
高的谐波由 L P F 衰减并返回 I C602。其相位与基准频率 5k H z
的相位进行对比。
通过相位对比产生的相位差信号由一个滞后超前式环路滤
波器转换为 D C 电压。该 D C 电压被输入 I C604 反相放大器并
与调制信号合成。该 D C 电压被输入用于控制 V C X O 振荡频率
16.8MHz. 的 X600 控制电压端子。
16.8M H z 震荡信号被送入 Q603 缓冲放大器。缓冲放大器的
输出信号用作发射机主 PLL 电路的基准频率信号。