Kenmore 796.4107 31 Series Скачать руководство пользователя

Страница: 9 / 59

4. INSTALLATION & TEST

Before servicing, ask the customer what the trouble is.

When installing or repairing the washer, put on long sleeve gloves and safety glasses.

Check the setup (power supply is 120V, remove the transit bolts, level the washer...)

Check with the troubleshooting guide.

Plan your service method by referring to the disassembly instructions.

Service the unit.

After servicing, operate the appliance to see whether it functions correctly.

• Remove the 4 shipping bolts

with the supplied wrench.

Do first lower side to remove easily.

•

Keep the shipping bolts and
spanner for future use.

•

Insert the 4 caps (provided)
into the hole.

• Turn clockwise to raise;

counterclockwise to lower.

• Turn the leveling feet to adjust

the appliance.

STANDARD INSTALLATION

The appliance should be installed as follows:

REMOVE THE SHIPPING

BOLTS

INSTALL THE APPLIANCE

ON A FLAT AND FIRM SURFACE

ADJUST THE

LEVELING

Содержание 796.4107 31 Series




























































Результаты поиска

Содержание 796.4107 31 Series

Отзывы:

Похожие инструкции для 796.4107 31 Series

Бренды по названию

Популярные бренды

Kenmore 796.4107 31 Series, Руководство по обслуживанию

Результаты поиска

Содержание 796.4107 31 Series

Отзывы:

Похожие инструкции для 796.4107 31 Series

Бренды по названию

Популярные бренды