manualshive.com logo in svg

Kenmore 796.4107 31 Series, Руководство по обслуживанию

Поделиться
Скачать
Kenmore 796.4107 31 Series Скачать руководство пользователя страница 27

28

HEATING ERROR

Is                 displayed?

Check the connectors at the
main PCB, the heater and the
thermistor. Are the
connectors loose or
disconnected?

Is the connector connected to
thermistor disconnected or
disassembled?

[Note]

The temperature sensing circuits on the main
PCB are very simple, consisting only of resistors
and capacitors. Problems with wiring or
connections in the thermistor circuit are the
most likely cause for this error. Be sure to
check ALL connections and wiring thoroughly.
The main PCB should only be replaces as a last
resort, as it is unlikely to be the cause.

Check the thermistor
resistance. Is the resistance
correct according to the
chart?

(Refer to 9-7 thermistor
assembly.)

Are the thermistor terminals
dry and free of corrosion?

Steam generator heater

Wash heater

Steam generator thermistor

Wash thermistor

Check the resistance of the
heater. Is the resistance
between 12

and 18

?

(Refer to 9-6 Heater
assembly.)

Yes

Yes

Yes

Yes

Yes

Yes

No

No

No

No

Reconnect or
repair
the connector.

Replace the
HEATER
ASSEMBLY.

Replace the
THERMISTOR
ASSEMBLY.

Replace the
THERMISTOR
ASSEMBLY.

Reconnect or
repair
the connector.

Proceed to next step at right

Содержание 796.4107 31 Series




























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды