Kenmore 796.4107 31 Series Скачать руководство пользователя

Страница: 11 / 59

TEST OPERATION

Preparation for
washing.

Press the POWER button.

Press the
START/PAUSE button.

Check the water heating
function.

Check the automatic
reverse rotation.

Check the water supply.

Check the drain and spin
functions.

Press the
START/PAUSE button.

Water removal.

• Connect the power plug to

the outlet.

• Connect the inlet hose.

• Listen for a click to determine if

the door has locked.

• Press the Wash Temp button

and the present temperature will
be displayed.

• Check if the drum rotates

clockwise and counterclockwise.

• Check if water is supplied

through the detergent dispenser.

• If SERVICE is needed during

check, remove the remaining
water by pulling out the hose cap.

• Listen for a click to determine

if the door is unlocking.

• Power off and the power on.
• Press the SPIN SPEED button.
• Press the START/PAUSE button.
• Check the spin and drain

functions.

Содержание 796.4107 31 Series




























































Результаты поиска

Содержание 796.4107 31 Series

Отзывы:

Похожие инструкции для 796.4107 31 Series

Бренды по названию

Популярные бренды

Kenmore 796.4107 31 Series, Руководство по обслуживанию

Результаты поиска

Содержание 796.4107 31 Series

Отзывы:

Похожие инструкции для 796.4107 31 Series

Бренды по названию

Популярные бренды