Kenmore 630.13952 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 51

Kenmore 630.13952 Скачать руководство пользователя страница 9

OPERATION

702_58300000149896_ara_en_b

P(X) Program codes

P0

= Functional test - used for assembly

(do not use)

P1

= Customer service test program

(see E(X) error codes)

P3

= Endurance / Life test

(do not use)

P4

= Control coding

(see C(X) control codes)

E(X) Error codes

E0

= No errors

E1

= Heating error

E2

= NTC error

E3

= Filling error

E4

= Water switch cannot be positioned

E5

= Safety float water level reached

E6

= Aqua sensor error

C(X) Control codes

C9

= Sales demo mode

Codes

C1

through

C9

are possible, depending on the model.

HINT:

Customers pushing and holding

Cancel-Reset

buttons while turning

dishwashers on can see strange displays. Whenever you get call about a
“strange” display, check if the customer put the dishwasher into the test
program or some other program.

Sales demo (showroom) program

Entering sales demo program

Enter the special program mode – see section IIIE. Before releasing the two
buttons held while you turned the dishwasher on, note the coding on the digital
display (e.g. “

C2

”) -- the dishwasher must be returned to this code for resale.

Push button “

B

” repeatedly until the display shows sales demo program mode

“

P4

”. Push button “

C

” to confirm it.

Push button “

B

” repeatedly until the display shows sales demo code “

C9

”. Push

button “

C

” to confirm it.

Turn power off and then back on. The dishwasher is now in demo mode -- all
button lights will light up.

«
...
7
8
9
10
11
...
»

Содержание 630.13952




















































Отзывы:

Нет отзывов