Kenmore 630.13952 Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 51

Kenmore 630.13952 Скачать руководство пользователя страница 29

Repair

To flip dishwasher upside-down

Tools needed: T20 Torx screwdriver, Phillips screwdriver and pliers

.

1. Turn off water and electricity. Disconnect dishwasher mounting

brackets

(1)

.

2. Remove toe kick by removing two Phillips screws and tilting toe kick

out from dishwasher

(2)

.

3.

Disconnect water line and electric supply

(3)

.

4. Pull

dishwasher

out,

place a pad or cardboard on the floor and carefully

flip the dishwasher upside-down

(4)

.

5.

Remove four base screws from front of dishwasher

(5)

.

6.

Remove two screws securing water valve to base. There’s no need to
disconnect valve wire harness or inlet hoses

(6)

.

7.

Pull wire harness connector from rear of terminal box

(7)

.

8.

Push latch on base-mounted control to disconnect it from base

(8)

.

9.

Remove both door springs from base

(9)

.

10. Remove two tank screws from rear of dishwasher

(10)

, disconnect both

rubber circulation pump supports

(11)

and carefully lift up base from

dishwasher

(12)

.

702_58300000149896_ara_en_b

«
...
27
28
29
30
31
...
»

Содержание 630.13952




















































Отзывы:

Нет отзывов