manualshive.com logo in svg

Kenmore 630.13952, Руководство пользователя, Страница: 8 / 51

Поделиться
Скачать
Kenmore 630.13952 Скачать руководство пользователя страница 8

OPERATION 

 

Changing basic features 

Some features can be changed on the fascia panel. 

End of cycle tone 

The 

End of cycle tone volume

 can be changed. 

 

Turn the dishwasher off and then push and hold the right 

Cancel Reset 

button 

while turning the dishwasher on – release buttons when a tone sounds or the 
right 

Cancel Reset 

button LED lights up.   

Pushing the right 

Cancel Reset 

button changes the setting – push it until the 

tone is at the desired volume (or the tone stops if it’s to be turned off).  Push the 
on/off button to save the setting. 

702_58300000149896_ara_en_b 

IIIC.  Entering special programs and coding 

Controls contain codes for sales demo mode, factory tests, customer service 
test program, dishwasher configuration and error codes.   

 

While pushing (and holding) 

any two

 wash cycle buttons, turn the dishwasher 

on with the on/off switch. The current coding (e.g. “

C2

”) will show in the display 

or LED's until you release the buttons.  After releasing the buttons, LED “

B

” will 

be lit and LED “

C

” will flash, confirming you’re in the special programs menu. 

Push button “

B

” repeatedly until you’ve selected your desired program 

(see 

P(X) Program codes, “P1” or “P4” -- programs “P0” and “P3” are factory tests 
that aren’t to be used).

 

Содержание 630.13952




















































Отзывы:

Нет отзывов