Kenmore 630.13952 Скачать руководство пользователя страница 49

Страница: 49 / 51

Technical Specifications

702_58300000149896_ara_en_b



Unsatisfactory washing results

Incorrect amount of detergent.

Utensils incorrectly arranged or rack overloaded.

Spray arm rotation blocked by utensils.

Spray arm nozzles need cleaning.

Filters not properly fitted into position.

Unsuitable cycle selected.

VII. Technical

Specifications



Dishwasher ratings

– Dishwashers are rated 120VAC, 60 Hz, 15A, 1450W (max.).

Maximum amp draw when heaters running ~ 11A.



Heater ratings

– 120VAC, 1200W, flow-through, heats water ~ 2ºF / minute.



Noise level –

Dependent on model, from 44 db – 56 dB.



Circulation pump ratings (BLDC motor)

– 120VAC, 60 Hz, 100W (~ .13 HP), 3-phase.



Drain pump ratings

– 110 - 127 VAC, 60 Hz, 35W, .84A, 17

Ω

(9-vane)



Water inlet pressure range –

From 5

–

120 psi (.3 – 8.27 bar).



Circulation pump flow rate

– Approximately 60 liters/minute (~ 15.85 gallons/minute)

at a pressure of 420 mbar (6.1 psi).



Drain pump flow rate

– Approximately 10 liters/minute (~ 2.64 gallons/minute) at a

delivery height (head) of .9m (2.95’).



Water inlet valve flow rate

– Approximately 2 liters/minute (~ .5 gallons/minute).

Содержание 630.13952




















































Результаты поиска

Содержание 630.13952

Отзывы:

Kenmore 630.13952, Руководство пользователя, Страница: 49 / 51

Результаты поиска

Содержание 630.13952

Отзывы: