Kenmore 630.13952 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 51

Kenmore 630.13952 Скачать руководство пользователя страница 16

COMPONENTS

Siphoning

Siphoning

may occur in any type of drain pump when low water flow allows a

siphon (suction) to develop, pulling waste water back into the pump. Sump
check valves along with air gaps/high loops prevent siphons from being created.

Terminal connections (Rast 5 connectors)

Rast 5 terminal connectors provide more positive connections than spade
terminals.

Johnson Tee installations (Washington State)

Drain pumps in installations with Johnson Tees (in Washington State) must use
stronger 4-vane pumps (

607468

).

Standard 9-vane drain pumps (

642239

) are quieter

and smoother than 4-vane pumps.

Water fill assembly

The water fill assembly is easily accessed from the left side.

Time fill

The time-fill water inlet system doesn’t have a diaphragm or water level switch.
Dishwasher controls allow water to fill for a specific time, relying on consistent
water flow through the water inlet valve to provide the correct water level.

702_58300000149896_ara_en_b

«
...
14
15
16
17
18
...
»

Содержание 630.13952




















































Отзывы:

Нет отзывов