background image

5

Thank You

 for purchasing a Kenmore water heater. Properly

installed and maintained, it should give you years of trouble free
service. If you should decide that you want the new water heater
professionally installed by Sears call 1-800-4-MY-HOME

®

. They

will arrange for prompt, quality installation by Sears authorized
contractors.

Abbreviations Found In This Instruction Manual:

UL - Underwriter’s Laboratories

CSA - Canadian Standards Association

ANSI - American National Standards Institute

NFPA - National Fire Protection Association

ASME - American Society of Mechanical Engineers

GAMA - Gas Appliance Manufacturers Association

EPACT - Energy Policy Act

This gas-fired water heater is design certified by UL
Underwriter’s Laboratories under American National Standard/
CSA Standard for Gas Water Heaters ANSI Z21.10.3 • CSA
4.3 (current edition).

•  Read the “Safety Precautions” section, page 3 of this manual

first and then the entire manual carefully. If you don’t follow
the safety rules, the water heater will not operate properly. It
could cause DEATH, SERIOUS BODILY INJURY AND/OR
PROPERTY DAMAGE.

This manual contains instructions for the installation, operation,
and maintenance of the gas-fired water heater. It also contains
warnings through out the manual that you must read and be
aware of. All warnings and all instructions are essential to the
proper operation of the water heater and your safety. Since
we cannot put everything on the first few pages,

 READ THE

ENTIRE MANUAL BEFORE ATTEMPTING TO INSTALL OR
OPERATE THE WATER HEATER.

The installation must conform with these instructions and the
local code authority having jurisdiction.  In the absence of
local codes, installations shall comply with the following:

In the United States

: The National Fuel Gas Code ANSI

Z223.1/NFPA 54.  This publication is available from the
Canadian Standards Association, 8501 East Pleasant Valley
Rd, Cleveland Ohio 44131, or The National Fire Protection
Association, 1 Batterymarch Park, Quincy, MA 02269.

If after reading this manual you have any questions or do not
understand any portion of the instructions, call the Sears
Service Center.

Carefully plan the place where you are going to put the water
heater. Correct combustion, vent action, and vent pipe
installation are very important in preventing death from
possible carbon monoxide poisoning and fires.  See
figures 1 and 8 through 13.

Examine the location to ensure the water heater complies
with the 

Facts to Consider About the Location

 section in this

manual.

For California installation this water heater must be braced,
anchored, or strapped to avoid falling or moving during an
earthquake. See instructions for correct installation
procedures. Instructions may be obtained from your local
dealer,  wholesaler, public utilities or California Office of the
State Architect, 400 P Street, Sacramento, CA 95814.

Massachusetts Code requires this water heater to be installed
in accordance with Massachusetts 248-CMR 2.00: State
Plumbing Code and 248-CMR 5.00.

Complies with SCAQMD rule #1146.2 and districts having
equivalent NOx requirements.

CUSTOMER RESPONSIBILITIES

PRODUCT SPECIFICATIONS

RECO

RECO

RECO

RECO

RECOVER

VER

VER

VER

VERY

Y

Y

Y

Y

MINIMUM

MINIMUM

MINIMUM

MINIMUM

MINIMUM

DIMENSIONS

DIMENSIONS

DIMENSIONS

DIMENSIONS

DIMENSIONS

T

T

T

T

TANK

ANK

ANK

ANK

ANK

TYPE

TYPE

TYPE

TYPE

TYPE

RA

RA

RA

RA

RATE G

TE G

TE G

TE G

TE GAL

AL

AL

AL

ALS

S

S

S

S.....

VENT PIPE

VENT PIPE

VENT PIPE

VENT PIPE

VENT PIPE

DIAMETER

DIAMETER

DIAMETER

DIAMETER

DIAMETER  IN INCHES (mm)

 IN INCHES (mm)

 IN INCHES (mm)

 IN INCHES (mm)

 IN INCHES (mm)

MODEL

MODEL

MODEL

MODEL

MODEL

CAP

CAP

CAP

CAP

CAPA

A

A

A

ACITY

CITY

CITY

CITY

CITY

OF

OF

OF

OF

OF

BTU

BTU

BTU

BTU

BTU

PER HOUR

PER HOUR

PER HOUR

PER HOUR

PER HOUR

INCHES

INCHES

INCHES

INCHES

INCHES

INCHES

INCHES

INCHES

INCHES

INCHES

 HEIGHT T

 HEIGHT T

 HEIGHT T

 HEIGHT T

 HEIGHT TO

O

O

O

O

 NUMBER

 NUMBER

 NUMBER

 NUMBER

 NUMBER

IN G

IN G

IN G

IN G

IN GAL

AL

AL

AL

ALS (L

S (L

S (L

S (L

S (LTRS)

TRS)

TRS)

TRS)

TRS)

G

G

G

G

GAS

AS

AS

AS

AS

RA

RA

RA

RA

RATE

TE

TE

TE

TE

@ 100°F RISE

@ 100°F RISE

@ 100°F RISE

@ 100°F RISE

@ 100°F RISE

(mm)

(mm)

(mm)

(mm)

(mm)

(mm)

(mm)

(mm)

(mm)

(mm)

J

JJ

JJA

A

A

A

ACKET T

CKET T

CKET T

CKET T

CKET TO

O

O

O

O

P

153.338073

74 (280)

NATURAL

75,100

72.8

4" (102)

26 1/2" (673)

61 1/8" (1,553)

153.338003

98 (371)

NATURAL

75,100

72.8

4" (102)

27 3/4" (705)

69 3/4" (1,772)

Содержание 153.338003





























Отзывы: