manualshive.com logo in svg

Kendro Heraeus Biofuge haemo, Инструкция по эксплуатации

Поделиться
Скачать
Kendro Heraeus Biofuge haemo Скачать руководство пользователя страница 49

Troubleshooting 

 

45

Error 

Behavior of the centrifuge 

Possible cause(s) and measures to be taken 

 

Centrifuge is exceptionally 
noisy. 

1.  Stop the centrifuge by pressing the "stop" key, in case of 

emergency pull mains plug. 

2.  Wait until the centrifuge stands still. 
3.  Check whether the rotor is properly loaded. 
4.  Check whether a broken vessel, damage to the rotor or 

motor malfunction was responsible for the noise. 

5.  If you cannot locate and solve the problem, call Service. 

 

br 

Mains connection interrupted 
during run 

If the plug was pulled inadvertently, plug in again.  
Wait for about 75 seconds. The centrifuge comes to a stop 
without braking. 

 

E-1 or E-12 

 

Rotor does not start 

Pull mains plug and plug in again. 
If the error persists, call Service. 

 

E-3 

No braking current; drive out 
of order, rotor stops without 
braking 

 

Lid opened during run. 

Wait until the rotor has come to a complete stop (check 
window in the lid). Pull mains plug and plug in again. If error 
persists, call nearest Service. 

Motor overheated. 

Room temperature too high or insufficient air cooling. Pull 
mains plug and wait 30 min. Check all vents and clean with 
small brush. 

 

Содержание Heraeus Biofuge haemo

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды