manualshive.com logo in svg

Kendro Heraeus Biofuge haemo, Инструкция по эксплуатации

Поделиться
Скачать
Kendro Heraeus Biofuge haemo Скачать руководство пользователя страница 44

Maintenance and care 

 

40

Rotor and rotor chamber must be treated with a neu-
tral, universal disinfectant. Best suited for this purpose 
are disinfectant sprays, ensuring that all rotor and 
accessory surfaces are covered evenly. 
 

• 

Please use 70% ethanol for disinfection. 

 

Please note the safety measures and 
handling hints when applying these 
substances! 

 

For other disinfectants please consult KENDRO 

 

Services! 

• 

You may disinfect the rotor and the accessories as 
described in the following section. Be sure to follow 
the pertinent safety procedures for handling infec-
tious material. 

1.  Pull mains plug. 
2.  Unscrew the rotor chuck. 
3.  Grab the rotor with both hands and pull it perpen-

dicularly off the drive shaft. 

4. Remove the centrifuge tubes and adapters, and 

disinfect them or dispose of them as necessary. 

5. Treat the rotor and the rotor lid according to the 

instructions given for the disinfectant (soaking in liq-
uid or spraying). You must strictly observe the 
specified action times! 

6.  Turn the rotor head down and drain off the disinfec-

tant. Thereafter thoroughly rinse rotor and lid with 
water. 

7.  Dispose of the disinfectant according to valid regula-

tions. 

8.  Aluminum rotors have to be treated with anticorro-

sive protective oil subsequently. 

 

 

Содержание Heraeus Biofuge haemo

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды