Kelvinator Air Conditioning
installation 9
8 installation
Kelvinator Air Conditioning
Upper Hook
Lower Hook
Cushioning
material
5. Piping and wrapping
Bundle the tubing, connecting cable, and drain hose with
tape securely and evenly as shown page 13.
• Because the condensed water from rear of the indoor
unit is gathered in the ponding box and is piped out of
the room, do not put anything else in this box.
Connecting
pipe
Wrapping belt
Drain hose
Indoor unit
Ponding box
Pipe room
Connecting
cable
caution
• Connect the indoor unit first, then the outdoor unit.
• Do not allow the piping to be exposed out from the back
of the indoor unit.
• Be careful not to let the drain hose become slack.
• Heat insulate the connecting piping.
• Be sure that the drain hose is located at the lowest side
of the bundle. Locating at the upper side can cause drain
pan to overflow inside the unit.
• Never cross connect or inter wind the power wire with
any other wiring.
• Run the drain hose sloped downward to drain out the
condensed water smoothly.
3. Connecting Pipe and Drainage Installation
1 Run the drain hose sloping downward. Do not install the
drain hose as illustrated below.
Do not block water flow with a rise.
Do not put the end of the
drain hose into water.
2 When connecting an extension drain hose, insulate the
connecting part of the extension drain hose with a shield
pipe, do not let the drain hose become slack.
Connecting pipe
1 For the left-hand and right-hand piping, remove the pipe
cover from the side panel.
2 For the rear-right-hand and rear-left-hand piping, install
the piping as shown. Bend the connecting pipe to be laid
at a height of 43mm or less from the wall.
3 Fix the end of the connecting pipe. (Refer to Tightening
Connection in REFRIGERANT PIPING CONNECTION)
Right-hand piping
Side Part cover
Left-hand piping
Rear-right piping
Rear-left piping
.
.
.
.
.
.
.
. .
.
. .
.
.
.
.
. .
.
.
. .
.
.. .
.
.
. .
.
.. .
.
. .
.
.
.
.
.
.
.
.. .
.
.
. .
.
.
.
.
.
. .
.
. . .
..
.
.
.
.
. .
.
.
.
.
.
.
. .
.
.
.. ..
.
.
.
. .
.
.
.
. .
. .
.
.
.
.
. .
.
..
.
. .
.
.
.
.
.
. .
.
.
.
.
.
. .
.
.
.
.
.
.
.
.
.
.
. ..
.
.
.
.
.
.
.
......
..
.
.
.
.. .
4
3
Indoor unit outline Connecting pipe
Installation
Indoor
Outdoor
5
-7
m
m
Wall
(7.0kw) and (8.0kw) model)
A
40
B
Right rear side
refrigerant
pipe hole 65
Installation plate
Indoor unit outline
Left rear side
refrigerant
pipe hole 65
15cm or more to ceiling
12cm or more
to wall
12cm or more
to wall
( (3.5kw) model,
)
<(6.2kw) model
<(3.5kw) model: (A: 710, B: 250/ A:790, B:265)
(3.5kw) model: (A: 790, B:265)
90
40
45
15cm or more to ceiling
Indoor unit outline
Installation plate
30
5
Right rear side
refrigerant
pipe hole 65
Left rear side
refrigerant
pipe hole 65
12cm or more
to wall
12cm or more
to wall
850
45
90
45
45
2
7
2
80
489
(>(6.2kw)model)
12cm or more
to the wall
to the wall
12cm or more
5
0
15cm or more to the ceiling
Indoor Unit Outline
380
Hooked Part
380
998
32
2
119
130
65
65
130
50
Above 12cm to
the wall
Above 12cm to
the wall
Above 15cm to
the ceiling
32
5
55
95
95
55
1250
815
257
178
55
58
Pipe hole
Hooked Part Hooker Part
Pipe hole
Indoor unit outline
Indoor
Outdoor
5
-7
m
m
Wall
(7.0kw) and (8.0kw) model)
A
40
B
Right rear side
refrigerant
pipe hole 65
Installation plate
Indoor unit outline
Left rear side
refrigerant
pipe hole 65
15cm or more to ceiling
12cm or more
to wall
12cm or more
to wall
( (3.5kw) model,
)
<(6.2kw) model
<(3.5kw) model: (A: 710, B: 250/ A:790, B:265)
(3.5kw) model: (A: 790, B:265)
90
40
45
15cm or more to ceiling
Indoor unit outline
Installation plate
30
5
Right rear side
refrigerant
pipe hole 65
Left rear side
refrigerant
pipe hole 65
12cm or more
to wall
12cm or more
to wall
850
45
90
45
45
2
7
2
80
489
(>(6.2kw)model)
12cm or more
to the wall
to the wall
12cm or more
5
0
15cm or more to the ceiling
Indoor Unit Outline
380
Hooked Part
380
998
32
2
119
130
65
65
130
50
Above 12cm to
the wall
Above 12cm to
the wall
Above 15cm to
the ceiling
32
5
55
95
95
55
1250
815
257
178
55
58
Pipe hole
Hooked Part Hooker Part
Pipe hole
Indoor unit outline
2. Drill a hole in the wall
1
Determine hole
positions according to
the diagram detailed in
Fig.5. Drill one (1) hole
( 65mm) slanting slightly
to outdoor side.
2 Always use wall hole
conduit when drilling
metal grid, metal plate
or the like.
Correct orientation of Installation Plate
Indoor unit installation
1. Fit the Installation Plate
1 Fit the installation plate horizontally on structural parts
of the wall with spaces around the installation plate.
2 If the wall is made of brick, concrete or the like, drill eight
(8) 5mm diameter holes in the wall. Insert Clip anchor for
appropriate mounting screws.
3 Fit the installation plate on the wall with eight (8) type
“A” screws.
Note: Fit the Installation Plate and drill holes in the wall
according to the wall structure and corresponding
mounting points on the installation plate.
(Dimensions are in “mm” unless otherwise stated)
4. Indoor unit installation
1 Pass the piping through the hole in the wall.
2 Put the upper claw at the back of the indoor unit on
the upper hook of the installation plate, move the indoor
unit from side to side to see that it is securely hooked.
3 Piping can easily be made by lifting the indoor unit
with a cushioning material between the indoor unit
and the wall. Remove cushioning material after the
piping is finished.
4 Push the lower part of the indoor unit up on the wall,
Then move the indoor unit from side to side, up and
down to check if it is hooked securely.