kelda BubbleSpa 95005000 Скачать руководство пользователя страница 3

Important Safety Information

This product requires a hot and a cold water supply in addition to 

an electrical connection (see Electrical section on page 16 & 17 

for details). This product is not an electric shower.

Products manufactured by Kelda Showers are safe and without 

risk provided they are installed, used and maintained

in accordance with our instructions and recommendations.

DO NOT operate the unit if the showerhead becomes damaged.

DO NOT restrict flow out of shower by placing an obstruction in 

front of the showerhead nozzles.

DO NOT allow children to play with the shower

DO NOT allow children to use the shower without supervision

General

1. 

Read all of these instructions before installation and retain 

them for later use.

2. 

DO NOT take risks with plumbing or electrical equipment.

3. 

Isolate electrical and water supplies before proceeding with 

the installation.

4. 

The showerhead must be cleaned regularly with descalant 

to remove scale and debris (see Maintenance section on 

page 21).

5. 

This product is not suitable for mounting into steam rooms 

or steam cubicles.

6. 

The shower should not be installed in an outdoor 

environment, including sheltered areas.

7. 

DO NOT spray water at the BubbleSpa showerhead as this 

risks damaging the electronics.

Plumbing

1. 

The plumbing installation must comply with water 

regulations, building regulations or any particular regulations 

as specified by local water company or water undertakers 
and should be in accordance with BS EN 806 (Specifications 

for installations inside buildings conveying water for human 

consumption. Operation and maintenance).

2. 

IMPORTANT! The hot and cold-water supply pipes must be 
flushed to clear debris from before connecting to water inlets 

on the shower.

3. 

DO NOT use excessive force when making connections to 

the mixer.

4. 

All plumbing connections must be completed before making 

the electrical connections.

  

5. 

Water  Pressure:  A  2  bar  system  is  recommended  as  a 
minimum,  if  using  a  low  pressure  (Gravity  fed)  system  a 
suitable pump will be required. Your BubbleSpa shower is 
designed  to  perform  best  between  8-10L/min  and  will  not 
produce bubbles with a flow rate below 6L/min. Using the 
BubbleSpa shower without a Kelda supplied flow regulator 

will void the warranty and negatively affect the performance 

of the product.

Electrical

1. 

The installation must comply with BS 7671 ‘Requirements 
for electrical installations’ (IEE wiring regulations), building 
regulations or any particular regulations as specified by the 

local electrical supply company.

2. 

In  accordance  with  ‘The  Plugs  and  Sockets  etc.  (Safety) 
Regulations  1994’,  this  appliance  is  intended  to  be 
permanently connected to the fixed wiring of the electrical 

mains system. 

3. 

A 32A 30 mA Residual Current Breaker Operator (RCBO) 
MUST  be  installed  in  all  UK  electric  and  pumped  shower 

circuits. This may be part of the consumer unit or a separate 

unit.

4. 

Each  shower  must  be  connected  to  a  3A  switched  fused 
spur  which  is  easily  accessible.  Switch  off  at  fused  spur 

for maintenance or if not in use for extended periods. This 

is a safety procedure recommended with all electrical 

appliances.

5. 

Make sure all electrical connections are tight to prevent 

overheating.

6. 

As with all electrical appliances it is recommended to have 

the shower and installation checked at least every two years 

by a competent electrician to ensure there is no deterioration 

due to age and usage.

Flashing Lights

To enhance the visual impact of the bubbles this shower uses 

flashing light effects, with a minimum frequency of 72Hz.  This 
is  accordance  with  safety  guidance  from  the  IEEE  (IEEE 
1789-2015)  and  is  safely  above  the  3-30Hz  range  (commonly 
identified as values to be avoided for people with photosensitive 

conditions). 

The  visual  effect  of  the  lighting  modes  will  vary  depending  on 

ambient lighting and the environment in which it is installed (see 

page 20 for more details on Bubble Modes). 

Anyone diagnosed with a condition which could be triggered by 

flashing lights should seek further medical advice. 

3

Содержание BubbleSpa 95005000





























Отзывы: