Keithley S530 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 123

Keithley S530 Скачать руководство пользователя страница 19

Section 2: Linear Parametric Test Library

S530/S540 KTE Linear Parametric Test Library (LPTLib) User's Manual

2-10

S530-900-01 Rev. E / September 2017

Specify the default system speed mode

Starting with Keithley Test Environment (KTE) software version 5.6, you can specify one of the
following speed modes as the default for your system:

FAST:

Produces faster measurements than previous KTE versions, with little or no effect on data

correlation. This mode is the default setting starting with version 5.6.

LEGACY:

A system speed mode that you can specify if you experience problems with the data you

are getting in the fast mode. This mode has speed and resolution performance similar to those in KTE
versions 5.5.1 or earlier.

CUSTOM:

Allows you to optimize your system by making adjustments to delay, filtering, and

analog-to-digital (AD) conversion settings.

The S530/S540 can be set up to automatically run in any of these modes by changing the value of
the

MODE

parameter in the

[SYSTEM SPEED MODE]

section of the system

$KIHOME/IC/icconfig_<QMO>.ini

file.

You can also set the speed mode for a specific module by adding the

setmode

command

KI_SYSTEM_SPEED_MODE

modifier to your test sequence. For more information about the

setmode

command and available modifiers, see

(on page 3-74).

For information about setting the default system speed mode in the

icconfig_<QMO>.ini

file, see

Editing the icconfig_<QMO>.ini file

(on page 2-11).

Fixed range versus autorange measurements

Use fixed-range measurements whenever possible. Depending on the measurement, this can
significantly increase the speed of the test sequence.

Fix-range trigger instruments

When you are using triggers, you should fix-range the triggering instrument with the value of the
trigger. If you do not do this, the trigger command forces a measurement to be made after each
sweep point, and the measuring instrument autoranges. Autoranging noticeably increases the total
test execution time.

Use combination commands

Do not use individual

force

X

and

meas

X

commands to sweep a set of points. Use the

sweep

X

command, which incurs significantly less overhead.

«
...
17
18
19
20
21
...
»

Содержание S530




























































































































Отзывы:

Нет отзывов