Keithley 2110-100 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 35

background image

In this section:

Introduction .............................................................................. 1-1

Control software ....................................................................... 1-1

Environmental conditions ......................................................... 1-3

Calibration considerations ........................................................ 1-3

Recommended test equipment ................................................ 1-4

Calibration code ....................................................................... 1-4

Introduction

This manual provides calibration and verification procedures for the Keithley Instruments Model 2110

5-1/2-Digit Multimeter. The procedures are performed using remote programming (SCPI commands)

over the USB interface using the KI-Tool software.

Control software

You must have one of the following items installed on the remote interface in order to obtain the

proper VISA layer:
Keithley I/O Layer 5.0 or greater (included on the CD-ROM that came with your Model 2110)
NI-VISA 3.1 or greater
Agilent I/O Library Suite 14.2 or greater
1. Install the USB device driver and KI-Tool software from the Keithley Instruments Model 2110

Product Information CD.

2. Connect the Model 2110 to the USB port and launch the KI-Tool software.
3. Verify that correct model number is displayed in the upper right-hand corner of the tool. See

Figure 1 for details.

4. Test the communications link between the Model 2110 and the control software by clicking

several function buttons and verify that the Model 2110 responds accordingly. See the figure

below for more details.

Section 1

Calibrating and adjusting the Model 2110

«
...
6
7
8
9
10
...
»

Содержание 2110-100




































Отзывы:

Нет отзывов

Похожие инструкции для 2110-100

Бренд: Stalwart Страницы: 6

Бренд: DMioTECH Страницы: 4

Бренд: Steren Страницы: 12

Бренд: Draper Страницы: 8

Бренд: Kusam-meco Страницы: 12

Бренд: Kusam-meco Страницы: 12

Бренд: Kusam-meco Страницы: 16

Resi-Pro 310 Series

Бренд: IDEAL Страницы: 3

MaschineRMikroMK3

Бренд: Reason Страницы: 50

Бренд: Mannesmann Страницы: 57

Бренд: GB Страницы: 3

Бренд: HT Страницы: 84

Бренд: Conrad Страницы: 91

Бренд: koban Страницы: 8

Бренд: Retlux Страницы: 244

Бренд: Jensen Страницы: 15

Бренд: Jensen Страницы: 23

Бренд: Gamry Страницы: 46

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды