Keithley 2000-Scan Скачать руководство пользователя страница 44

Страница: 44 / 86

Scanning channels

Scanner channels are scanned by configuring scan channels and programming the

Model 2001 or 2002 to perform a scan. The following paragraphs outline step-by-step
procedures for performing basic scanning from the front panel and over the IEEE-488 bus.

Front panel scanning

Step 1: Configure channels

Use CONFIG-CHAN to select the measurement functions for each of the scanner channels

as follows:

Press CONFIG-CHAN. The instrument will display the following menu:

CONFIGURE CHANNELS

INTERNAL-CHANS EXTERNAL-INPUTS

Select INTERNAL-CHANS, then press ENTER. The multimeter will display the
following menu:

SET INTERNAL CHANS

1=DCV 2=DCV 3=DCV 4=DCV 5=DCV

Using the cursor keys, select the desired channel (press the right cursor key to display
channels 6 through 10).

Using the range keys, select the desired measurement function: DCV, ACV,

Ω

2W,

Ω

4W,

FRQ, TMP, ALT, --- (None).

Repeat steps 3 and 4 for each of the channels you wish to scan. NOTE: Select --- (none)
to omit a channel from the scan list.

After selecting all measurement functions, press ENTER.

Press EXIT to return to normal display.

Step 2: Configure and start scan

Configure the scan as follows:

Press CONFIG-SCAN. The Model 2001/2002 will display the following:

SCAN OPERATION

INTERNAL EXTERNAL

Select INTERNAL, then press ENTER.

Press SCAN, and follow the prompts to configure scanning. See the following
paragraphs for details.

3-10

Operation

Содержание 2000-Scan























































































Результаты поиска

Содержание 2000-Scan

Отзывы:

Похожие инструкции для 2000-Scan

Бренды по названию

Популярные бренды

Keithley 2000-Scan, Инструкция по эксплуатации

Результаты поиска

Содержание 2000-Scan

Отзывы:

Похожие инструкции для 2000-Scan

Бренды по названию

Популярные бренды