
9
C)
Install Motor Assembly to Hanger Plate Assembly /
Ԋ၆ีଢ଼ᐠಢӇՍ
ӤݖಢӇ
1
1
Insert Ball Joint into the Hanger Plate
Assembly.
將球形接頭插入吊板組件。
2
2
Adjust the Ball Joint to insert the Hanger Guide Rib into its slot. Refer to
in the illustration below.
Make sure the Ball Joint Holder is placed onto the Switch Cover. Refer to
in the illustration below.
調整球形接頭以將吊架導向擋邊插入其狹槽。如下圖所指的
。
確定將球形接頭固定點放在開關罩上。如下圖所指的
。
CAUTION /
ݧཎ
Fix Ball Joint correctly to Hanger Plate Assembly.
Can cause product not to operate if Switch Cover is not
been pressed down.
正確地將球形接頭安裝至吊板組件。
若沒壓下開關罩可導致產品無法操作。
Do not push Switch Cover with other object, except using
Ball Joint given.
Can cause fi re, explosion, short circuit and electrical shock.
除了所提供的球形接頭,切勿使用其他物體推開關罩。
這會導致火災、爆炸、短路和電擊。
3
3
Remove Hexa Nut, Spring Washer, and Plain Washer from Carl Bolt at hole no. 1. Pass Safety Wire through Safety Wire
Outlet. Fix Safety Wire to No. 1 Carl Bolt as shown. Tighten the removed Plain Washer, Spring Washer and Hexa Nut
onto the Carl Bolt.
將六角形螺帽、彈簧墊圈和普通墊圈從
1
號孔的卡爾螺栓取出。將保險線穿過保險線出口。如圖所示,將保險線固定至
1
號卡爾螺栓。鎖緊之前拆下的普通墊圈、彈簧墊圈和六角形螺帽在卡爾螺栓。
CAUTION /
ݧཎ
Safety Wire must be fi xed correctly.
Can cause Ceiling Fan to drop and cause
injuries.
保險線必須正確地安裝。
這可導致吊扇掉落和導致受傷。
ATTENTION /
ཎ
For Plaster Ceiling, install Safety Wire using M5
screw as shown in Figure 4 in section B2.
對於石膏天花板,請使用 M5 螺絲安裝保險線
(如 B2 部份圖 4 所示)。
Ball Joint /
球形接頭
Hanger Plate Assembly /
吊板組件
Concrete Ceiling /
混凝土天花板
Motor Shaft /
發動機轉動軸
Hexa Nut /
六角形螺帽
Safety Wire Outlet /
保險線出口
1
Carl Bolt /
卡爾螺栓
Safety Wire /
保險線
Plain Washer /
普通墊圈
Spring Washer /
彈簧墊圈
Concrete Ceiling /
混凝土天花板
Switch Cover /
開關罩
Hanger Guide Rib /
吊架導向擋邊
Ball Joint Slot /
球形接頭狹槽
Ball Joint Holder /
球形接頭固定點
< Top View - For Viewing Purpose Only >
<
頂視圖 - 供參觀之用
>
R48SP.indd 9
R48SP.indd 9
4/15/2013 5:20:42 PM
4/15/2013 5:20:42 PM