
6
Check Point After Installation /
Ԋ၆ࡣޟᔮᡛᘈ
Check /
ᔮࢥ
1. Ensure the Screws (6 pieces) for securing the Blade are tightly screwed. /
確定扇翼螺絲(6枚)已被鎖緊。
B1)
Install Hanger Plate Assembly to Concrete Ceiling /
Ԋ၆ӤݖಢӇՍ
ᏗπЈ߆ݖ
1
1
Make 5 holes on the concrete ceiling. 4 holes
(no. 2, 3, 4, 5) with diameter 8.5mm (depth 45mm) and
hole no. 1 with diameter 6.5mm (depth 30mm).
在混凝土天花板鑽 5 個孔。4 個孔 (2、3、4、5 號)
直徑 8.5毫米 (深度
45毫米) 和 1 號孔直徑 6.5毫米
(深度
30毫米)。
(Hole no. 1 is for Safety Wire).
(
1
號孔用於保險線)。
2
2
Install Carl Bolt.
安裝卡爾螺栓。
1. Drill holes on the concrete ceiling.
在混凝土天花板鑽孔。
2. Use blower to remove dust in the holes.
使用吹除機清除孔內的灰塵。
3. Insert the Carl Bolt.
插入卡爾螺栓。
4. Tighten the supplied Plain Washer, Spring Washer, Hexa Nut to all 5 Carl Bolts. This is to ensure the Carl Bolt is
fi rmly embedded in the ceiling.
鎖緊附帶的普通墊圈、彈簧墊圈、六角形螺帽至所有 5 枚卡爾螺栓。這是為了確保卡爾螺栓穩固地固定在天花板。
5. Remove Hexa Nut, Spring Washer, and Plain Washer from hole no. 2, 3, 4 and 5 Carl Bolt. Make sure Carl Bolt is
remained strong on the ceiling.
將六角形螺帽、彈簧墊圈和普通墊圈從
2
、
3
、
4
號孔取出並拆除
5
枚卡爾螺栓。確定卡爾螺栓仍然緊緊地固定在天
花板上。
3
3
Remove Hanger Supporter Screws and Hanger
Supporter from the Hanger Plate Assembly and
retain for step C-4 (Page 9).
將吊架支架螺絲和吊架支架從吊板組件拆除並保留
用於步驟 C-4(第 9 頁)。
c
d
e
b
a
Drill /
鑽孔機
Blower /
吹除機
Carl Bolt /
卡爾螺栓
Hammer /
錘子
Hanger Plate
Assembly /
吊板組件
Hanger Supporter
Screw /
吊架支架螺絲
Hanger Supporter /
吊架支架
(Remove both Screws and Hanger Supporter) /
(拆除螺絲及吊架支架)
60°
110mm
4-Ø8.5
Ø6.5
1
2
3
4
5
60°
Ø94
R48SP.indd 6
R48SP.indd 6
4/15/2013 5:20:41 PM
4/15/2013 5:20:41 PM