Kaysun COMPAK KHP 15/190 ACS1 Скачать руководство пользователя

Страница: 25 / 52

Kaysun combo type KHP 15/190 ACS1 Manual MCAC-RTSM-2017-09

11. Maintenance

Recommended regular maintenance table

Checking

item

Checking content

Checking

frequency

Action

Air filter (inlet/outlet)

Every month

Clean the filter.

Anode rod

Every half year Replaced if it has been used out.

Inner tank

Every half year Clean the tank.

E-heater

Every half year Clean the E-heater.

PT valve

Every year

Operate the hander of PT valve to

ensure that waterways are clear.

If water dose not flow freely when operating the hander, replace PT vale with a

new one.

Check the connection between power supply plug and socket and ground wiring regularly.

In some cold area (Below 0

°C

), if the system will be stopped for a long time, all the water

should be released in case of freezing of inner tank and damage of E-heater.

It is recommended to set a lower temperature to decrease the heat release, prevent scale

and save energy if the outlet water volume is sufficient.

Before shutting the system down for a long time:

Shut down the power supply;

Release all the water in the water tank and pipeline, and close all the valves.

Check the inner components regularly.

Anode rod replaced

Turn off the power supply and water inlet valve.

Open hot water tap, and decrease the pressure of the inner container.

Open the drainage valve, and drain out the water, until there is no water flow out.

Get off the anode rod.

Replace with a new one, and make sure effective sealed.

Open cold water inlet tap until water flows out from outlet tap, then turn off water outlet tap.

Power on, and then restart the unit.

Anode Rod

Содержание COMPAK KHP 15/190 ACS1





















































Результаты поиска

Содержание COMPAK KHP 15/190 ACS1

Отзывы:

Похожие инструкции для COMPAK KHP 15/190 ACS1

Бренды по названию

Популярные бренды

Kaysun COMPAK KHP 15/190 ACS1, Техническое руководство

Результаты поиска

Содержание COMPAK KHP 15/190 ACS1

Отзывы:

Похожие инструкции для COMPAK KHP 15/190 ACS1

Бренды по названию

Популярные бренды