KAWASHIMA PRO2000i Скачать руководство пользователя страница 32

Страница: 32 / 39

5-4

5.4 Air Filter Maintenance

hould be

performed every 6 months or 100 hours. The
air filter may need to be cleaned more
frequently when using in unusually wet or
dusty areas.

1. Remove the screws

①

and then

remove the cover

②

2. Remove the screws

①

and then

remove the air filter case cover

②

3. Remove the foam element

①

4. Wash the foam element in

solvent and dry it.

5. Oil the foam element and

squeeze out excess oil. The
foam element should be wet but
not dripping.

NOTE:

Do not wring out the foam element

when squeezing it. This could cause it to
tear.

6. Insert the foam element into the

air filter case. Be sure the foam
element sealing surface matches
the air filter so there is no air leak.

NOTE:

The engine should never run

without the foam element.

7. Install air filter case cover,

cover, and screws.

Содержание PRO2000i








































Результаты поиска

Содержание PRO2000i

Отзывы:

Похожие инструкции для PRO2000i

Бренды по названию

Популярные бренды

KAWASHIMA PRO2000i, Инструкция по эксплуатации и руководство пользователя

Результаты поиска

Содержание PRO2000i

Отзывы:

Похожие инструкции для PRO2000i

Бренды по названию

Популярные бренды