KAWASHIMA PRO2000i Скачать руководство пользователя страница 31

Страница: 31 / 39

5-3

5.3 Engine Oil Replacement

Initial replacement of the engine oil is after
one month or 20 hours of operation.

1. Place the generator on a level

surface and warm up the engine for
several minutes. Then stop the
engine and turn the Fuel Tap knob to

“OFF”

and the Fuel Tank Cap Air

Vent knob to

“OFF”

2. Remove the screws

①

and then

remove the cover

②

3. Remove the oil filler cap.

4. Place an oil pan under the

engine. Tilt the generator to
drain the oil completely.

5. Return the generator to a level

surface.

Note:

DO NOT tilt the generator when

adding engine oil. This could result in
overfilling and damage to the engine.

6. Add engine oil to the upper level as

seen in the diagram

①

Recommended engine oil:

• YAMALUBE 4 (10W-40),SAE 10W-30 or

10W-40

• SAE#30
• SAE#20

• SAE10W

Recommended engine oil grade:

API Service SE type or higher

Engine oil quantity:

0.4 Litre

7. Install oil filler cap, cover, and

screws.

Содержание PRO2000i








































Результаты поиска

Содержание PRO2000i

Отзывы:

Похожие инструкции для PRO2000i

Бренды по названию

Популярные бренды

KAWASHIMA PRO2000i, Инструкция по эксплуатации и руководство пользователя

Результаты поиска

Содержание PRO2000i

Отзывы:

Похожие инструкции для PRO2000i

Бренды по названию

Популярные бренды