KAWASHIMA PRO2000i Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 39

background image

1-1

SECTION 1:

SAFETY INSTRUCTIONS AND WARNINGS

1.1 Symbol Usage

This manual contains important information that you need to know and understand
in order to assure YOUR SAFETY and PROPER OPERATION OF EQUIPMENT.
The following symbols help you recognize this information. Please read the
manual and pay attention to these sections.

Save These Important Safety Instructions!

Read and understand all of these safety instructions. Be sure to
retain them for future use.

WARNING!

WARNINGS INDICATE A CERTAINTY OR STRONG
POSSIBILITY OF PERSONAL INJURY OR DEATH IF
INSTRUCTIONS ARE NOT FOLLOWED.

CAUTION:

CAUTIONS INDICATE A POSSIBILITY OF EQUIPMENT
DAMAGE IF INSTRUCTIONS ARE NOT FOLLOWED
PROPERLY.

Note:

Notes give helpful information

Gasoline powered and electrical generating products can cause serious injury or
death, or damage to other equipment or property, if the operator does not strictly
observe all safety rules and take precautionary actions.

«
...
2
3
4
5
6
...
»

Содержание PRO2000i








































Отзывы:

Нет отзывов

Похожие инструкции для PRO2000i

Бренд: Samsung Страницы: 32

Бренд: Samsung Страницы: 32

Бренд: Tait Страницы: 2

Бренд: Uniden Страницы: 76

Бренд: Eberg Страницы: 14

Бренд: Shindaiwa Страницы: 42

Yakumo DVD Travelle

Бренд: YAKUMO Страницы: 40

Бренд: Hyundai Страницы: 24

615 - DVP 615 - DVD Player

Бренд: Zenith Страницы: 40

Бренд: Akai Страницы: 2

Бренд: Briggs & Stratton Страницы: 8

WEDECO SMOevo PLUS Series

Бренд: Xylem Страницы: 179

TOWER LIGHT CUBE+ HYBRID

Бренд: Generac Power Systems Страницы: 74

Бренд: Fenton Страницы: 16

Бренд: Soen Страницы: 12

Бренд: Hytera Страницы: 4

Бренд: LENCO Страницы: 1

Бренд: Boston Acoustics Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды