Kathrein MSK 125 Скачать руководство пользователя

Страница: 30 / 64

TV MEASUREMENT

ANALOGUE AND DIGITAL CABLE TV RECEPTION

In CABLE mode the MSK 125 can be set to the “Analogue” and “DVB-C” reception types.

ANALOGUE CABLE / DVB-C SWITCH

Press once

Analogue cable TV

press again

DVB-C

press again

= Back to

analogue cable TV

[CABLE A/D]

HF STANDARD SWITCH - ANALOGUE CABLE (DEMOD MENU)

In TV mode the MSK 125 can measure the following standards:

• B/G standard
• L standard
• D/K standard
• I Standard
• M/N standard
• M1 standard (Japan)

Calling up the DEMOD menu

[DEMOD]

Call up menu for standard change-over and

demodulator

setting.

[1] ... [6]

Select standard

After that the DEMOD menu is exited

automatically.

[OK]

Press

[OK]

[DEMOD]

, to exit the Demod

menu without any changes.

Command overview:

If you wish to keep the settings unchanged, press [OK].

Please note that the selected standard remains even after the
device is switched off.

Note

Содержание MSK 125

































































Результаты поиска

Содержание MSK 125

Отзывы:

Похожие инструкции для MSK 125

Бренды по названию

Популярные бренды

Kathrein MSK 125, Руководство по эксплуатации

Результаты поиска

Содержание MSK 125

Отзывы:

Похожие инструкции для MSK 125

Бренды по названию

Популярные бренды