Kärcher SE 4001, Оригинальное руководство пользователя

Страница: 13 / 146

– 8
 Switch on sprayer (position I).
 Apply detergent solution and allow to react for 5
minutes (vacuuming is switched off).
 Clean the surface just like you would with light/nor-
mal soiling.
 After cleaning the carpets, reclean them using
clear, warm water and waterproof if needed.
 Rinse the spray tubes in the appliance as follows:
Fill the detergent container with about 1 liter of
clear water.
Hold the nozzle above the drain, and switch on the
spraying pump until the clear water has been con-
sumed.
Note
To use the device as a multi-purpose vacuum cleaner,
the spray handle and the spray hose can be removed.
Illustration
 Remove the spray hoses and mounting clips from
the suction hose and suction tubes.
 Press the two locking noses on the sides and pull
the spray handle off the handle.
ATTENTION
Always ensure that the filter bag is inserted for dry vac-
uuming.
Better filtration can be achieved by using a cartridge fil-
ter (special accessories).
Container and accessories must be dry, otherwise dirt
may adhere.
 Select the desired accessories and attach to the
suction pipes or directly to the handle.
Illustration
 Insert a filter bag.
 Select the desired accessories and attach to the
suction pipes or directly to the handle.
 Switch on suction (position I).
 Insert the hard surface inlay into the floor nozzle.
The bristles should point towards the front.
 Work without the hard surface insert.
Illustration
 Use the surrounding air separator to adapt the suc-
tion force.
Note:
Close the surrounding air separator again after
use!
ATTENTION
Do not use a filter bag!
Note: If the container is full, a float closes the suction
opening, and the appliance works at a higher speed.
Switch off the appliance immediately, and empty the
container.
 Attach the accessories to vacuum moisture or wet-
ness to the suction tubes or directly to the handle.
 Switch on suction (position I).
Illustration
 Open the sliding air regulator when vacuuming up
larger quantities of water. Close it again after use.
 Empty the full reservoir (refer to chapter "Empty
reservoir").
 Turn off the appliance.
 Empty the full reservoir (refer to chapter "Empty
reservoir").
 Rinse the reservoir thoroughly with clear water.
 Remove the accessories from the appliance after
each use and disassemble the hose, nozzle and
extension tubes.
Note : Possibly remaining water can drip out, there-
fore you should place these into the shower or
bathtub.
 Flush the accessories separately under running
water and let air dry.
 Clean the foam filter under running water; let it dry
before reinserting it.
 Leave the appliance open to let it dry.
 Storing the appliance . Store the accessories on
the appliance and store in dry rooms.
With an uneven spray jet.
Illustration
 Loosen nozzle attachment and pull out, clean or re-
place spray nozzle.
1 x year or as needed.
Illustration
 Turn the lock and loosen it. Take out the sieve and
rinse it with water.
 Fill up fresh water reservoir.
 Check the fresh water reservoir for correct fit.
 Detergent pump defective, contact customer ser-
vice.
 Clean the spray nozzle of the spray ex floor nozzle.
 Close the surrounding air separator at the handle.
See diagram 11
 Accessories, suction hose or suction tubes are
clogged, please remove the obstruction.
 Filter bag is full: Insert new filter bag.
 Cleaning the foam filter.
 Fill up fresh water reservoir.
 Plug in the mains plug.
 The overheat alarm has been triggered, please al-
low appliance to cool down.
Heavy soiling or stains
End wet cleaning process
Use as multi-purpose vacuum cleaner
Vacuuming hard surfaces
Vacuuming carpeted floors
Vacuuming up water
Shutting down
Maintenance and Care
Cleaning the device
Clean the sieve in the fresh water reservoir
Faults
No water exiting from nozzle
Spray stream uneven
Insufficient vacuum performance
Detergent pump noisy
Appliance is not running
13 EN