background image

10

Operations

Installation

Place machine in a convenient location providing 
ample support, drainage and room for maintenance.

Location

The location should protect machine from damaging 
environmental conditions, such as wind, rain and 
freezing.

1.

The machine should be run on a level surface 
where it is not readily influenced by outside 
sources such as strong winds, freezing tempera-
tures, rain, etc. The machine should be located 
considering accessibility for the replacing of 
components and the refilling of detergents, adjust-
ments and maintenance. Normal precautions 
should be taken by the operator of the machine to 
prevent excess moisture from reaching the 
machine.

2.

It is recommended that a partition be made 
between the wash area and machine to prevent 
direct spray from the spray gun from coming in 
contact with the machine. Excess moisture 
reaching the power unit or electrical controls will 
reduce the machine’s life and may cause electrical 
shorts.

3.

During installation of the machine, beware of 
poorly ventilated locations or areas where exhaust 
fans may cause an insufficient supply of oxygen. 
Sufficient combustion can only be obtained when 
there is a sufficient supply of oxygen available for 
the amount of fuel being burned. If it is necessary 
to install a machine in a poorly ventilated area, 
outside fresh air may have to be piped to the 
burner and a fan installed to bring the air into the 
area.  

4.

Do not locate near any combustible material. Keep 
all flammable material at least 20 feet away.

Allow enough space for servicing the machine.

Local code will require certain distances from 

floor and walls. (Two feet away should be ade-
quate).

WARNING: Avoid small areas or near exhaust fans. 

Gas Codes

Confer with local gas company and with proper 
municipal officials regarding any specific code or regu-
lations governing the installation. The installation must 
conform to local codes (NFPA 54).

Electrical

The machine, when installed, must be electrically 
grounded in accordance to local codes. Check for 
proper power supply using a volt meter; check the 
serial plate for the correct requirements.

Gas Piping

This machine shall be rigidly connected to the gas 
piping outlet and equipped with external manual shut-
off valves adjacent to such machine. All gas piping shall 
be approved and installed in accordance with the 
Uniform Mechanical Code.

Install a gas union in the gas line adjacent to and 
upstream from the control manifold and downstream 
from the manual main shut-off valve. A 1/8" NPT 
plugged tapping accessible for test gauge connection 
shall be installed immediately upstream of the gas 
supply connection for the purpose of determining the 
gas supply pressure to the burner, and to prevent 
damage to gas valve.

If a manual gas shut off valve is not in the gas supply 
line within six feet of the machine and in an accessible 
location, one shall be installed.

Union Location

Union Connection

The following pipe sizes are just recommendations. 
Always consult a local plumber and venting contractor 
for local codes and regulations during installation.

Landa VNG Operator’s Manual  8.913-939.0 - AB

Manual  

Shut-Off 

Valve

1/8" NPT Plugged Pressure Gauge  

Port Location

Union

Drop

Floor Level

Содержание Landa VLP Series



















































































Отзывы: