– 6
Illustrations on Page 2
Illustration
Remove the safety lock from the device.
Fill the boiler with a maximum of 200 ml of fresh tap
water.
Note
Please use the provided measuring cup.
When filling in the water, observe the marking (max.
200 ml).
Illustration
Screw in safety cap.
Illustration
Insert the mains plug into a socket.
Indicator lamp glows green.
Illustration
The steam cleaner is ready for use after approx. 3
minutes.
Illustration
Connect the accessories to the steam nozzle.
Illustration
Push the child lock at the top (steam button un-
locked).
Push the steam button.
The steam cleaner is ready to use.
Illustration
If necessary, connect the required accessories
(see Chapter "Use of the accessories") with the
steam nozzle.
In order to do so, fit the open end of the accessory
to the steam nozzle and push it on until the unlock-
ing button of the steam nozzle snaps in place.
Illustration
Use the extension tubes if necessary. To do so,
connect one or both extension tubes to the steam
nozzle. Insert the required accessories on the free
end of the extension tube.
Push the child lock at the bottom (steam button
locked).
Illustration
To detach the accessory parts, press the unlocking
button and pull the items apart.
Notes
In case of continuous use of commercially available
distilled water, no descaling of the boiler is neces-
sary.
You can reduce the heating-up time by using warm
water.
Remove the safety lock from the device.
Fill the boiler with a maximum of 200 ml of fresh tap
water.
Note
Please use the provided measuring cup.
When filling in the water, observe the marking (max.
200 ml).
Screw the safety cap back onto the device.
Place the unit securely on a firm surface.
Insert the mains plug into a socket.
Indicator lamp must glow.
Note
After approx. 3 minutes the steam cleaner is ready for
use.
Push the child lock at the top.
Actuate the switch to release steam.
Notes
Upon initial start-up a small cloud of smoke may
exit the steam nozzle. The appliance requires a
short run-in time. At first, the escaping steam is ir-
regular and moist, some water drops may leak out.
The escaping amount of steam increases continu-
ously until the maximum amount is reached after
approx. one minute.
Do not tilt the appliance too much to the side during
cleaning work (max. angle 30°).
Otherwise the steam cleaner "spits" water.
Water needs to be filled into the boiler, if the steam vol-
ume decreases during work and no more steam is emit-
ted in the end.
Note
The safety lock cannot be opened as long as slight pres-
sure remains in the boiler.
Illustration
Disconnect the mains plug from the socket.
Push the steam button until no more steam is es-
caping. Now, the boiler of the appliance is depres-
surized.
Push the child lock at the bottom.
Remove the safety lock from the device.
Fill the boiler with a maximum of 200 ml of fresh tap
water.
Screw the safety cap back onto the device.
Insert the mains plug into a socket.
Push the child lock at the top.
The steam cleaner is ready to use.
Illustration
Disconnect the mains plug from the socket.
Push the steam button until no more steam is es-
caping. Now, the boiler of the appliance is depres-
surized.
Push the child lock at the bottom.
Illustration
Empty water out.
Illustration
Coil the mains power cable around the water tank.
Allow accessories to dry afterwards.
Store the appliance at a dry and frost-proof loca-
tion.
ATTENTION
Material damage due to a stuck safety lockIf the safety
lock is not removed after cleaning, there is a possibility
that the lock could get stuck in the thread. After clean-
Quick Reference
Operation
Attaching the Accessories
Removing the Accessories
Fill up with water
Turning on the Appliance
Refilling Water
Turning Off the Appliance
Storing the Appliance
10
EN
