Kärcher KM 105/100 R Bp, Руководство пользователя

Страница: 15 / 22

-
11

Danger
Risk of injury! While working around the lift/
tilt emptying mechanism, raise the waste
container to its highest point and secure.
 Insert safety support into the piston rod
for the lifting cylinder and secure it.

DANGER
Risk of burns!
Allow the machine sufficient time to cool
down before carrying out any maintenance
and repair work.
 Park the sweeper on an even surface.
 Turn the program selection switch to
"OFF".
 Remove key (intelligent key).
 Allow device to cool down sufficiently.
 Park the sweeper on an even surface.
 Connect air pressure testing device to
tyre valve.
 Check air pressure and adjust if required.
For permissible tyre inflation pressure
see Chapter "Technical specifications".
 Park the machine on an even surface.
 Check stability of ground. Lock the ap-
pliance to ensure that it does not roll off.
 Place the jack at the relevant position
point.
NOTICE
Use a suitable commercially available vehi-
cle jack.

Loosen the central wheel bolt by ap-
prox. 1 rotation using a suitable tool.

Raise machine using vehicle jack.
 Unscrew and remove the wheel bolt.
 Remove wheel.
 Have a defective wheel repaired or re-
placed in a specialist workshop.
 Fit the wheel and screw the wheel bolt
all the way in and tighten it lightly.
 Lower machine using vehicle jack.
 Tighten the wheel bolt with the required
torque.
Tightening torque 49 Nm

Contact the customer service for the re-
moval of the drive.

Do not sit down on the driver seat.
 Turn the programme selector switch to
position C (drive).
 If the message > Please sit down on
the machine < appears on the display,
the safety function is given.
(only with devices with high emptying sys-
tem)
CAUTION
This inspection may only be carried out
when the machine has cooled down.
1 Hydraulic unit
2 Filler neck
Note: The side brush floating mounting ad-
justs the sweeping track as the bristles
wear down. The side brush must be re-
placed if it becomes too worn.
Recommendation : Replacing the side
brush at a remaining bristle length of ap-
prox. 10 cm.
 Park the machine on an even surface.
 Turn the programme selector switch to
"OFF" and remove the key (intelligent key).
Note : The side brush is raised.
 Unscrew all 3 star grip nuts at the bot-
tom of the side brush by hand. For this
purpose reach through the bristles of
the side brush.
 Remove the wiper blade.
 Clip new side brushes on to driver and
screw on.
 Park the sweeper on an even surface.
 With appliance with low emptying sys-
tem:
Turn the programme selector switch to
"OFF" and remove the key (intelligent
key).
Remove both waste containers.
 With appliance with high emptying sys-
tem:
Turn the programme selector switch to
position C (drive).
Lift the waste container and secure by
means of cylinder support.
Turn the programme selector switch to
"OFF" and remove the key (intelligent
key).
 Remove belts or cords from roller
brush.
The sweeping track of the roller brush is au-
tomatically adjusted by a system called
TEACH.
The condition of the roller brush can be
shown on the display.
 Turn the programme selector switch to
"ON".
 Push the direction key "upwards" or
"downwards" until the display >
usabil-
ity of the roller brush: ..% < appears.
Note: If the roller brush is heavily worn, the
indication > Usability of the roller brush
<20% < appears on the display.
Now, at the latest, the roller brush should
be replaced.
The replacement is required if the sweep-
ing result visibly decreases due to the wear
of the bristles or the indication >
Usability
of the roller brush <20% < appears on the
display.
Each roller brush half is attached to the
shaft by means of 2 screws. Both halves
are identical, which facilitates the installa-
tion.
 Park the machine on an even surface.
With appliance with low emptying system:
 Turn the programme selector switch to
"OFF" and remove the key (intelligent
key).
 Remove both waste containers.
Note : For the removal of the roller
brush dismount the centre bar first.
 Loosen the screw and remove the cen-
tre bar.
With appliance with high emptying system:
 Turn the programme selector switch to
position C (drive).
 Lift the waste container and secure by
means of cylinder support.
Maintenance Works
General notes on safety
Preparation
Check the tyre pressure
Remove rear wheel
Dismantling the drive
Check the function of the seat contact
switch
Checking hydraulic oil level at the
hydraulic unit
Checking the sweeping mirror of the
side-brushes
Replacing side brush
Checking roller brush
2
1
Check the sweeping mirror of the
sweeping roller
Replacing the roller brush halves
15 EN