Kärcher KM 105/100 R Bp, Руководство пользователя

Страница: 12 / 22

-
8
Note
The progress of the charging process is
shown via a bargraph (5 bars) on the display.
At the beginning of the charging process
5 lines can be seen briefly.
Little by little the 5 bars are filled (depend-
ing on the charging state of the battery at
the beginning of the charging process,
more slowly or faster). When the last bar is
filled, the battery is charged.
 Open left cover.
 Separate the battery plug and connect
the charger cable.
 Plug in mains connector and switch on
charger, if necessary.
With low-maintenance batteries
 Add distilled water after the charging
process has been completed; observe
the correct acid level. There are corre-
sponding indicators on the battery.
 DANGER
Danger of causticization!

Adding water to the battery in its dis-
charged state can cause the acid to leak.

Wear protective glasses and protective
clothing when handling battery acid.
Observe the regulations concerning the
handling of batteries!
몇
WARNING
Risk of damage!
 Use only distilled or desalinated water
(EN 50272-T3) for filling the battery.
 Do not add any substances (so-called
performance improving agents), else
warranty claims will not be entertained.
 Rinse thoroughly with lots of clear water
if acid gets into the eye or comes in con-
tact with the skin.
 Then consult a doctor immediately.
 Change clothing.
 Wash off the acid If it comes in contact
with the clothes.
 Unplug the charger from the mains.
 For devices with built-in charger :
Store the mains connection away in the
retainer and clip in the mains plug.

If the device does not have a built-in
charger
: Pull the mains plug off the
charger, reconnect the battery plug.
To be performed by the operator on a
daily basis!
The description of the checks and work be-
low can be found in Chapter "Care and
maintenance/maintenance work".
 Check safety function of the left cover
(device must not start while the cover is
open).
 Check function of seat contact switch.
 Check the roller brush and the side
brush for wear, foreign bodies and
wrapped belts
 During a standstill of the machine:
Check the drive pedal for ease of move-
ment in order to guarantee functional
reliability or timely detect a jamming of
the pedal.
 Empty waste container.
 Check tyre pressure.
 Check battery acid level.
 With appliances with high emptying
system
: Check filling level at the hy-
draulic unit.
 Pull seat adjustment lever inwards.

Slide seat, release lever and lock in
place.

Check that the seat is properly locked in
position by attempting to move it back-
wards and forwards.
Note: The max. load of the storage area is
20 kg.

Ensure safe fastening of the cargo.
Preconditions for the functioning operation
of the appliance are:
– The intelligent key (grey or yellow) with
the authorisation for the operation of the
appliance must be inserted in the key
slot of the control panel.
– The main switch must be in position 1.
– The programme selector switch may
not be in the "OFF" position.
– Waste container and left cover must be
closed and locked in place.
몇
CAUTION
Risk of damage!
 Always press the accelerator pedal
carefully and slowly. Do not jerkily
change from reverse to forward drive or
vice versa.
 The travel speed must be adapted to
the existing conditions.
1 Drive pedal
2 Driving direction switch
 Set the travel direction to forward using
the travel direction switch at the control
panel.

Press accelerator pedal down slowly.
 DANGER
Risk of injury!

When reversing, there must not be any
risk for third parties, have somebody
marshal the driver if necessary.
 Set the travel direction to reverse using
the travel direction switch at the control
panel.
 Press accelerator pedal down slowly.
 The accelerator pedal can be used to
vary the driving speed infinitely.
 Avoid operating the pedal fitfully.
 Release the accelerator pedal, the ma-
chine brakes automatically and stops.
Note : Should the device not come to a
stop, push the main switch to the "0" po-
sition for an "Emergency stop".
ATTENTION
Objects or loose obstacles may not be run
over or pushed.
 Stationary obstacles of a height of up to
6 cm can be slowly and carefully driven
over (only when the coarse dirt flap is
opened).
 Drive over stationary obstacles higher
than 6 cm (2
1/3
inch) only when using a
suitable ramp.
 DANGER
Risk of injury! If the bulk waste flap is open,
stones or gravel may be flung forwards by
the roller brush. Make sure that this does
not endanger persons, animals or objects.
CAUTION
Do not sweep up packing strips, wire or
similar objects as this may damage the
sweeping mechanism.
– Adjust the driving speed to the condi-
tions in order to achieve an optimal
cleaning result.
– Empty the waste container at regular in-
tervals during the sweeping operation.
Note : If mainly gravel was swept up
(high weight of the waste), empty the
waste container sooner.
With appliances with low emptying
system
: There is a marking for the
maximum filling level for gravel on the
waste container. The marking becomes
visible when the waste container is re-
moved.
– Lower the roller brush while cleaning
surfaces.
– Preferably perform the cleaning of side
edges with the right side brush.
– The sickle brush (optional) is only low-
ered during left cornering.
(2) Charging process KM 105/100(110)
R Bp
Information concerning accidents with a
risk of chemical burns
After charging
Start up
Prior to start/safety test
Operation
Adjusting driver's seat
Storage area
Starting up the appliance
Drive the machine
Drive forward
Reverse drive
Driving method
Brakes
Driving over obstacles
Sweeping mode
Information on the sweeping operation
12 EN