Kärcher KM 105/100 R Bp, Руководство пользователя

Страница: 16 / 22

-
12
 Turn the programme selector switch to
"OFF" and remove the key (intelligent
key).
1 Screws
2 Roller brush
 Unscrew both screws by hand and pull
the roller brush half from the shaft.

Insert new roller brush halves and tight-
en the screws (pay attention to the
marking "L" = left and "R" = right).
 Turn the roller brush by 180 °, loosen
and remove the screws from the sec-
ond roller brush half.
 Insert new roller brush half and tighten
the screws.
 Then ensure that the roller brushes are
safely locked in place.
With appliance with low emptying system:
 Reattach the centre bar, ensure proper
seating of the gaskets!
 Park the machine on an even surface.
 Turn the programme selector switch to
"OFF" and remove the key (intelligent
key).
Side brush and roller brush are raised.
1 Front sealing strip
2 Nut
3 Retaining plate front
4 Rear sealing strip
5 Screw
6 Forward travel direction
 Front sealing strip
Adjusting the sealing strip:
 Loosen the nuts by approx. 2 rotations,
do not completely unscrew them.
 Set the distance between the sealing
strip and the floor so that the bottom
edge trails behind at a distance of be-
tween 80-85 mm.
 Tighten nuts.
If worn, replace.
 For replacing the sealing strips unscrew
the nuts completley, insert new sealing
strip, fit retaining plate, adjust sealing
strips and screw down retaining plate.
 Rear sealing strip
Adjusting the sealing strip:
 Loosen screws by approx. 2 rotations,
do not completely unscrew them.
 Set the distance between the sealing
strip and the floor so that it tilts towards
the front with an overtravel of 15 -
20 mm.
 Tighten the screws.
If worn, replace.
 For replacing the sealing strips unscrew
the screws completley, insert new seal-
ing strip, fit retaining plate, adjust seal-
ing strips and screw down retaining
plate.
 Side sealing strips
Adjusting the sealing strip:
 Loosen screws by approx. 2 rotations,
do not completely unscrew them.
 To set the floor clearance, insert a
sheet with a thickness of between 1 and
3 mm under the sealing strip.
 Adjust sealing strip.
 Tighten the screws.
If worn, replace.
 For replacing the sealing strips unscrew
the screws completley, insert new seal-
ing strip, fit retaining plate, adjust seal-
ing strips and screw down retaining
plate.
몇 WARNING
Wear a dust mask when working around
the dust filter. Observe safety regulations
on the handling of fine particles.
Note : Wait at least 1 minute before remov-
ing the dust filter so that the dust can settle.
1 Lid with cleaning device
2 Screw
3 Support
4 Dust filter (flat-fold filter)
 Loosen screws.

Fold the lid up and secure it by means
of the support.
 Take out the dust filter.
 Check dust filter.
 Insert cleaned or new dust filter.
 Place support into retainer.
 Close the lid.
 Screw in the screws and tighten them.
 Have the suction blower checked for
leaks.
Check by customer service
 Check the drive belt of the roller brush
for tension, wear and function.
Check by customer service
 Replace defective fuse.
1 Pole fuse
2 Jumper
3 Nut
Note: A defective pole fuse may only be re-
placed by a Kärcher service technician or
an authorised expert. If this fuse is defec-
tive, check the usage conditions and the
entire control system.
Adjusting and replacing sealing strips
80-85 mm
15-20 mm
1
2
4
5
6
3
Check/replace dust filter
Check suction blower
Checking drive belt of roller brush
Replacing fuses
F1 Control CPU 5 A
F2 Main fuse
Pole fuse 175 A
F70 Charger 40 A
Pole fuse
2
3
1
16 EN