Kanardia miniDaqu Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 53

Kanardia miniDaqu Скачать руководство пользователя страница 34

7.4

Configuration

miniDaqu — Manual

Table 6:

Connection table for serial RS-232 bus.

DB9-ECU

Daqu Function

ECU

Pin 2

RS232 RX

RS232 TX

Pin 3

RS232 TX

RS232 RX (connection not required)

Pin 1

GND

N/C

7.4

Configuration

When configuring Daqu, correct Engine model must be selected. An example
of configuration dialog is illustrated on Figure 22.

Figure 22:

An example ULPower engine selection.

Select one of the following options:

ULPower RS-232

when ECU is connected using RS-232 serial connection.

ULPower CAN 125 kb/s

when ECU is connected using CAN. The communi-

cation speed is 125 kb/s. This speed was used ECUs delivered until
1.11.2018. Please check your ECU.

ULPower CAN 500 kb/s

when ECU is connected using CAN. The speed 500

kb/s is used in latest ECUs. Please check your ECU.

When additional Daqu channels are used, they must be properly configured.
A function selected by Daqu channel will override same function provided by
ECU or AUX.

8

MWfly Engines

CAUTION: This section is preliminary!

The content is not verified!

©

Kanardia

2019-2022

32

«
...
32
33
34
35
36
...
»

Содержание miniDaqu






















































Отзывы:

Нет отзывов