manualshive.com logo in svg

Kaise SK-8402, Инструкция по эксплуатации

Поделиться
Скачать
Kaise SK-8402 Скачать руководство пользователя страница 5

SK-8402 

取扱説明書（英文）

_P3

3

SAFETY PRECAUTIONS 

(strict observance is required)

WARNING

Do not drive the car keeping the instrument connected.

Unexpected accident, electric shock, fire, or damage to the instrument or the car may occur.

Do not work under the car when it is jacked up.

Unexpected accident may occur.

Do not open the battery cover keeping the instrument connected to the car.

Electric shock may occur.

Do not replace the battery with the wet hands.

Electric shock may occur.

Keep the instrument away from babies or children.

Important to prevent any accident, injury, or electric shock hazard.

Do not work in the dark place.

Unexpected accident, electric shock, fire, or damage to the instrument or the car may occur.

Do not point the tip of  Test Pin or Check Harness at the person.

Loss of eyesight or injury may occur.

Do not get the instrument wet.

Fire or electric shock may occur.

Содержание SK-8402













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды