Kaise SK-8402 Скачать руководство пользователя страница 37

Страница: 37 / 44

SK-8402

取扱説明書（英文）

_P35

SIMULATION TEST

⑥

Press SEL Key for 1 second or less in simulation
test mode to select RICH signal output or LEAN
signal output.

Do not apply the simulation test for titania 5V
O2 sensor to zirconia O2 sensor or titania 1V
O2 sensor. It may damage the O2 sensor and
ECU.

CAUTION

Do not take the simulation test for heater cable
or power supply cable during the electric car
components are activated. It may damage to
the instrument.

CAUTION

⑤

Press SEL Key for 1 second or more in stand-by
mode to enter simulation test mode. lights up
on LCD.

※

Confirm the selected O2 sensor type displayed
on LCD.

LEAN

RICH

APO

④

Connect red and black check harness connecting
plugs to the red and black straight plugs
respectively.

Red test lead straight plug

Red check harness

connecting plug

Black test lead straight plug

Black check harness

connecting plug

Содержание SK-8402













































Результаты поиска

Содержание SK-8402

Отзывы:

Бренды по названию

Популярные бренды

Kaise SK-8402, Инструкция по эксплуатации

Результаты поиска

Содержание SK-8402

Отзывы:

Бренды по названию

Популярные бренды