manualshive.com logo in svg

Kaise SK-8402, Инструкция по эксплуатации

Поделиться
Скачать
Kaise SK-8402 Скачать руководство пользователя страница 4

2

SK-8402 

取扱説明書（英文）

_P2

SAFETY PRECAUTIONS 

(strict observance is required)

WARNING

Be careful about your hands, gloves and clothes not to be caught in the engine belt or cooling fan.

Important to prevent injury.

Do not to touch the heated part of the engine such as exhausting parts.

Important to prevent burn injury.

Be careful not to catch your feet in the test leads.

Important to prevent injury.

Confirm that the shift lever is set to "Parking" position (set to "Neutral" for stick shift car).

The car runs accidentally and could cause unexpected accident, electric shock, or damage
to the instrument or the car.

Confirm that the parking brake is applied.

The car runs accidentally and could cause unexpected accident, electric shock, or damage 
to the instrument or the car.

Take the measurement or its preparation under well-ventilated environment.

Carbon monoxide poisoning may occur due to the engine running during the measurement.

Use the "car lift" when lifting the car for measurement preparation.

Important to prevent any accident.

Use the supplied test leads and cables when taking the measurement.

Important to prevent any accident, electric shock, or damage to the instrument or the car.

Содержание SK-8402













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды