manualshive.com logo in svg

Kaise SK-8402, Инструкция по эксплуатации

Поделиться
Скачать
Kaise SK-8402 Скачать руководство пользователя страница 22

SK-8402 

取扱説明書（英文）

_P20

20

PREPARATION FOR USE

⑥

Red and black check harnesses have good continuity 
if "OL" blinks on LCD. Otherwise, either or both of  
them should be disconnected.

⑦

Press  SEL  Key  for  1  second  or  more  to  finish 
simulation  test  mode  temporarily.  Press  SEL  Key 
again  for  1  second  or  more  and  enter  simulation 
test mode once again.

⑧

Connect two yellow check harness connecting plugs 
to the red and black straight plugs respectively.

⑨

Short-circuit two yellow male connecting terminals 
and press TEST Key for 1 second or less to output 
RICH signal.

⑩

Two yellow check harnesses have good continuity 
if "OL" blinks on LCD. Otherwise, either or both of 
them should be disconnected.
This concludes the check harness inspection.

RICH

Z

S

APO

RICH

Z

S

APO

Red test lead straight plug

Yellow check harness

connecting plug

Black test lead straight plug

Yellow check harness

connecting plug

Press TEST Key for 1 second or less with contacting
the tips of two yellow male connecting terminals.

O

2

 SENSOR CHECKER

SK-8402

TEST

SEL

Содержание SK-8402













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды