background image

Easidew Transmitter User’s Manual

Kahn Instruments

  

9

MAINTENANCE

MAINTENANCE

Calibration

Routine maintenance of the Easidew is confined to regular re-calibration by exposure 

of the Easidew to sample gases of known moisture content to ensure that the stated 

accuracy of the Easidew is maintained.  Calibration services traceable to the 

National 

Institute of Standards and Technology (NIST) are provided by Kahn Instruments.

Kahn Instruments offers a variety of re-calibration and exchange sensor programs to 

suit specific needs. A Kahn representative can provide detailed, custom advice (for Kahn 

Instruments contact information go to www.kahn.com).

Sensor Guard Replacement

The sensor is supplied with a white HDPE guard (standard) or a stainless steel guard 

(if specified at time or order). The method of replacement is the same for both types.

HDPE Guard

The  HDPE  guard  provides  <10μm  protection  to  the  dew-point  sensor.  It  is  designed 

to show any contamination and the guard should be changed if the surface becomes 

discolored.
When replacing the guard, care should be taken to handle the guard by the bottom part 

only. Replacement guards (EA2-HDPE) - pack of 10 - can be obtained by contacting 

Kahn Instruments (www.kahn.com).

          

 Ea

sid

ew

 34

 T

ra

ns

m

it

te

r

          

      

    

    

    

   

   

   

   

09

06

          

      R

ang

e: 

- 1

00

 / 

+2

0

                

      

     

 

  4

8 L

an

ca

st

er

 W

ay

 B

                

      

     

 

    

   

El

y, 

Ca

m

br

id

ge

s

                

      

     

 

    

   

   

   

   

   

 C

B

3N

                

      

     

 

    

   

   

   

Un

ite

K

in

g

                

     

 

     

  

M

IC

H

E

                 

     

     

    

   

 

In

st

ru

m

en

HANDLE, 

USING

GLOVES, BY 

BLACK PART

ONLY

Figure 11 

Replacement of HDPE Guard

Stainless Steel Guard

The  stainless  steel  guard  provides  <80μm  protection  to  the  dew-point  sensor.  It  is 

designed to show any contamination and the guard should be changed if the surface 

becomes discolored.
When replacing the guard, care should be taken to handle the guard by the bottom 

part only. A replacement guard (SSG) can be obtained by contacting Kahn Instruments 

(www.kahn.com).

Bonded Seal

If the installed bonded seal gets damaged or lost, a pack of 5 replacement bonded seals 

can be obtained by contacting Kahn Instruments, and quoting part number BS-58-PK5. 

Содержание Easidew





















Отзывы: