background image

Kaden Installation Manual  | 

15

5.  Outdoor unit installation

Install the unit by following local codes and regulations. They 
may differ slightly between different regions.

Installation instructions –  

Outdoor unit

Step 1: Select installation location

Before installing the outdoor unit, you must choose an 
appropriate location. The following are standards that will help 
you choose an appropriate location for the unit.

Proper installation locations meet the following standards:

 

Meets all spatial requirements shown in installation space 
requirements above.

 

Good air circulation and ventilation.

 

Firm and solid – the location can support the unit and will 
not vibrate.

 

Noise from the unit will not disturb others.

 

Protected from prolonged periods of direct sunlight or rain.

 

Where snowfall is anticipated, raise the unit above the base 
pad to prevent ice build-up and coil damage. Mount the 
unit high enough to be above the average accumulated 
area snowfall. The minimum height must be 45cm above 
the base pad.

DO NOT install unit in the following locations:

 

Near an obstacle that will block air inlets and outlets.

 

Near a public street, crowded areas, or where noise from 
the unit will disturb others.

 

Near animals or plants that will be harmed by  
hot air discharge.

 

Near any source of combustible gas.

 

In a location that is exposed to large amounts of dust.

 

In a location exposed to a excessive amounts of salty air.

Special considerations  

for extreme weather

If the unit is exposed to heavy wind:

Install unit so that air outlet fan is at a 90° angle to the 
direction of the prevailing wind. If needed, build a barrier in 
front of the unit to protect it from extremely heavy winds.  
See figures below.

If the unit is frequently exposed to heavy rain or snow:

Build a shelter above the unit to protect it from the rain or 
snow. Be careful not to obstruct air flow around the unit.

If the unit is frequently exposed to salty air (seaside):

Use outdoor unit that is specially designed to resist 
corrosion.

 

60cm 

above

30cm from 

back wall

30cm 

on left

60cm 

on right

200cm 

in front

Strong 

wind

Strong 

wind

Strong 

wind

Содержание KCS Series

































Отзывы: