Kaba Peaks Preferred Скачать руководство пользователя

Страница: 11 / 92

All Peaks key blanks are marked with a unique identification number. The Kaba key control contract and this

manual specify certain key control procedures. Breach of contract or failure to abide by factory key records

policies can result in loss of the product line.

Contracts specify that:

1. The blank ID number may not be removed, stamped-over, or altered in any way;
2. Parties under contract may not duplicate any keys without following proper key records

authorization procedures;

3. Key blanks may not be sold, lent, or given away;
4. Proper key records must be kept and authorization forms maintained.

Key Blank Identification Number and Peaks Contracts

Kaba Access Control employs the latest machining techniques to ensure smooth reliable operation through-

out a wide variety of cylinders to provide hardware to fit the full spectrum of security needs. Kaba uses high

quality brass to manufacture the plug and shell of each cylinder. All Kaba Peaks keys are made of nickel

silver which incorporates a large bow capable of receiving stampings and use by physically impaired people.

All Kaba Peaks family of reliable cylinders are designed and manufactured to stand up to the heaviest of

use over an extended life of many years.
The patented security features of Kaba’s Peaks Security Cylinders provide new capabilities to the standard

pin tumbler lock design without complicating the procedures involved in servicing the cylinder. Patent

protected Kaba Peaks keys use standard pin tumbler combination bittings, so standard code and duplicating

key machines can cut Peaks keys from key blanks that are produced by the factory.

Kaba Peaks Quality

Section 1 - 7

tio

Содержание Peaks Preferred





























































































Результаты поиска

Содержание Peaks Preferred

Отзывы:

Похожие инструкции для Peaks Preferred

Бренды по названию

Популярные бренды

Kaba Peaks Preferred, Техническое руководство

Результаты поиска

Содержание Peaks Preferred

Отзывы:

Похожие инструкции для Peaks Preferred

Бренды по названию

Популярные бренды