Kaba Peaks Preferred Скачать руководство пользователя

Страница: 34 / 92

Section 2 - 22

YALE

5300L grade 2 levers

8400-xx-1295-95

factory combinated then modify

8400-xx-1095

uncombinated and use*

3400-xx-1295-95

factory combinated then modify

3400-xx-1095

uncombinated and use*

*4700-80-2001 SA/3B tailpiece, vertical

*3450-80-2003 spacing washer

Field modification required.

YALE

5400 grade 1 knobs and 5300 grade 2 knobs

Retrofit for Yale No. 1801 cylinder

8400-xx-1254-54

factory combinated

8400-xx-1054

uncombinated

3400-xx-1254-54

factory combinated

3400-xx-1054

uncombinated

Same as 8400-xx-1055-55 cylinder below, but without tailpiece.

YALE

5400LN grade 1 levers

8400-xx-1255-55

factory combinated

8400-xx-1055

uncombinated and use*

3400-xx-1255-55

factory combinated

3400-xx-1055

uncombinated and use*

*3425-82-3012 tailpiece

*3425-00-4012 retainer pin (

" roll pin)

Same as 8400-xx-1054 cylinder above but with tailpiece.

YALE

5300LN grade 2 levers

8400-xx-1295-56

factory combinated

8400-xx-1095

uncombinated and use*

3400-xx-1295-56

factory combinated

3400-xx-1095

uncombinated and use*

*3450-80-2003 spacing washer

*3450-00-2000 lost motion tailpiece, vertical

large diameter

plug requires

J or K series

bottom pins

“95” plug & shell

with

small plug face

large diameter

plug requires

J or K series

bottom pins

“95” plug & shell

with

small plug face

cut line

SA/3B

YALE

6100 and 6200 series Monolocks

Retrofit for Yale No. 1801 cylinder

8400-xx-1255 (Yale monolock) factory combinated

8400-xx-1055 (Yale monolock) uncombinated

3400-xx-1255 (Yale monolock) factory combinated

3400-xx-1055 (Yale monolock) uncombinated

Same as 8400-xx-1054-54 cylinder below, but without rollpin and spacer.

Key-In-Knob Cylinders

Note:

Modify tailpiece using Yale tail-

piece as a template.

Содержание Peaks Preferred





























































































Результаты поиска

Содержание Peaks Preferred

Отзывы:

Похожие инструкции для Peaks Preferred

Бренды по названию

Популярные бренды

Kaba Peaks Preferred, Техническое руководство

Результаты поиска

Содержание Peaks Preferred

Отзывы:

Похожие инструкции для Peaks Preferred

Бренды по названию

Популярные бренды