Kaba Peaks Preferred страница 54 Скачать руководство пользователя

Страница: 54 / 92

Section 3 - 10

Peaks conventional cylinders are designed to be top loaded. Install the Peaks patent bottom and top pins in

the patent chamber immediately next to the plug face. Peaks Classic patent bottom pins are installed small

end down, whereas Peaks Preferred patent bottom pins are installed small end up. Install the Peaks patent

top pins small end down for both Peaks Classic and Preferred.

In the

system a number

top pin

should be seated above the patent top pin. In

use a number

top pin above the patent top pin.

Pin stacks

Consult the charts on pages 3 - 17 and 3 - 20 for the correct pins.

The Universal 8400-xx-1099 and the 8400-xx-1095 key-in-knob cylinder

have large diameter plugs and require longer bottom pins and the

8144-00-3004 patent bottom pin.

The Universal 3400-xx-1099 and the 3400-xx-1095 key-in-knob cylinder

have large diameter plugs and require longer bottom pins and the

6140-00-3004 patent bottom pin.

All conventional cylinders, Peaks Preferred/Classic use the same top

pins. Observe the specified pin stack heights. After loading the pins

install a 3800-00-4010 stainless steel tumbler spring in each chamber.

Staking

Place the cylinder in the correct cavity of the 3400-00-4000 staking fix-

ture. Set the correct curved spring cover in place over the springs and

hold it down with the staking tool.

Using a plastic or rawhide mallet, flatten the spring cover between the

flanges. Do not strike the bible flanges on key-in-knob cylinders. Bend-

ing or breaking the flanges breaks the patented hard coat on the shells

and can lead to corrosion.

The chrome key-in-knob cylinder shell requires a staking tool and new curved spring cover, 6440-00-2000.

Older staking tools had a thick blade. The blade must be narrowed to 0.125" to fit between the bible flanges.

• Work on a firm bench surface.

• Strike tools gently with a plastic or rawhide mallet.

• Do not use excessive force.

• Use Kaba original equipment.

These are the tools required for conventional cylinders:

Do not strike
bible flanges

Flatten the
spring cover
between them.

The 3400-00-4002 key-in-

knob staking tool and flat

spring covers are discon-

tinued. Do not use this or

similar tools on chrome

key-in-knob cylinders.

6440-00-4001

staking tool

3400-00-4000 staking

fixture for conventionals

Pinning Conventional Cylinders

Содержание Peaks Preferred





























































































Результаты поиска

Содержание Peaks Preferred

Отзывы:

Похожие инструкции для Peaks Preferred

Бренды по названию

Популярные бренды

Kaba Peaks Preferred, Техническое руководство

Результаты поиска

Содержание Peaks Preferred

Отзывы:

Похожие инструкции для Peaks Preferred

Бренды по названию

Популярные бренды