Kaba Peaks Preferred Скачать руководство пользователя страница 7

Страница: 7 / 92

Section 1 - 3

tio

150 spacing is used for Peaks small format interchangeable cores only! There are no conventional cylinders

or other large format interchangeable cores in 150 spacing. 150 small format interchangeable cores cannot

be interkeyed with the 140 family.

The pin-to-pin spacing is 0.150" in original Best small format interchangeable cores. Peaks small format

interchangeable cores are available in 6-pin and 7-pin lengths, and will retrofit any Best style housing.

In 150, the first pin chamber is very close to the back. In 140,

there is a

" gap between the first chamber and the back.

There are seven pin chambers in 6-pin Peaks small format

interchangeable cores: six operating pins plus the patent pin,

a constant in all cylinders. There are eight pin chambers in

7-pin small format interchangeable cores.

150

140

Pin chambers

closer to

face of core.

face of Peaks small format

interchangeable cores

8402/3402 rim

8800/3800 capped SFIC

8900/6800 spring cover SFIC

All the cores and cylinders in the 140 family can be

keyed together in the same patent protected system.

8400/3400 key-in-knob

140 and 150 are the actual pin-to-pin spacings in thousandths of an inch. 140 spacing is used in the

interkeyable family of conventional cylinders, interchangeable cores and removable cores. All 140 products

are 6-pin. There are actually seven pin stacks in a Peaks 140 core or cylinder. One pin chamber is used for

the patent pin stack and is constant in all Peaks products. The remaining six chambers are used

for combinating.

8144/6140 Corbin Russwin LFIC

8244/6240 Yale (6 pin) LFIC

8401/3401 mortise

The Peaks 140 Family

Peaks 150 – Small Format Interchangeable Cores only

6340 Medeco LFIC

8444/6440 Schlage LFIC

8544/6540 Sargent LFIC

PAT # 7181941

Содержание Peaks Preferred





























































































Результаты поиска

Содержание Peaks Preferred

Отзывы:

Бренды по названию

Популярные бренды

Kaba Peaks Preferred, Техническое руководство

Результаты поиска

Содержание Peaks Preferred

Отзывы:

Бренды по названию

Популярные бренды