background image

Prepare the door according to the table and diagram 
below, to suit the application.

375 mm

961 mm

961 mm

546 mm

546 mm

961 mm

[A]

[B]

375 mm

367mm

S14R/P

S14R/L

S14R/H

Code

S14R/S

Suit 1500

Low

High

Sample

With the 

top

 

remote lock

 connected to the

 top

 

rod

slide the

 free-end

 of the

 top rod

 though the

 top 

remote lock cutout.  

Repeat the above process for the 

bottom remote lock

.

 

 
Rod lengths for each application are given in the table
below for reference. If using the Adjustable Rod system, 
see over page for setup instructions.

Fit a supplied 

o-ring 

on each rod  60 - 80mm from the 

remote end (not needed for Adjustable Rods). 

Assemble corresponding 

rods

 to the 

top

 and 

bottom 

remote locks

, ensuring the 

UP arrows

 on the 

remote 

locks

 are pointing towards the top of the door.

NOTE:

 

DO NOT SCREW THE REMOTE LOCKS IN YET. 

top 
remote lock

bottom 
remote lock

o-ring

o-ring

rod 

free-ends

top 
remote lock

top cutout

bottom cutout

bottom 
remote lock

399 mm

985 mm

570 mm

TOP Rod

993 mm

578 mm

993 mm 

BOT. Rod

399 mm

399 mm

Suit 1500

Low

High

Sample

=[A]+24

mm

=[B]+32

mm

Formula

go to Step 3. 

Mark the cutout dimensions 

A

 and 

 on the

Measurement Guide

 provided.

NOTE: The standard cutout positions are pre-marked.

If you are fitting several doors with the same cutout 
dimensions, it is recommended that you securely tape 
the 

Measurement Guide

 to a benchtop or piece of 

timber. Then drill holes (4.5mm diameter) to locate and 
secure the rod ends while fastening. 

Follow this step if using Adjustable Rods, otherwise 

coupling

central hole

(large hole upwards)

rod length

 min. 100

coupling

 min. 100

rod

rod

drive pin and rolled pin 
flush inside the coupling

The 

coupling 

should be placed in the center between 

the two 

rod ends

, and have the larger 

central hole

 

facing upwards.

NOTE: If the distance between the straight rod ends and 
the bent rod ends is less than 100mm (as shown above) 
you must cut-down the rods enough to provide this 
clearance.

The 

rod ends

 must be pointing downwards into the

benchtop. If you are not drilling holes for the 

rod ends

you will need to place a flat block (10mm thick) under 
the 

coupling

.

Insert the 

steel rods

 into the brass 

coupling

 as shown.

tap with hammer until it is fully inside the 

coupling

.

CHECK THAT THE ROD ENDS ARE PARALLEL AND
POINTING STRAIGHT DOWN

Re-align if necessary and check the overall length.

Insert the 

rolled steel pin

 into the large 

central hole 

and 

rolled pin

 and hammer until it is fully inside the 

coupling

.

Place the pointed end of the 

drive pin

 into the top of the 

coupling

rolled pin

drive pin

central hole

The Adjustable Rod is now ready for installation.

rolled

pin

drive

pin

E TH

L

C

IS

Y

 P

C

A

E

C

R

 

K

E

A

S

G

A

IN

E

G

L

P

172

156

64

19

60

60

19

25

16 Slot Width

[A]

[B]

Centre Line

of Cutout

64

Illustrated fitting instructions 

ILLUSTRATED FITTING INSTRUCTIONS

S14R

multi-point rod kit

Austral

Lock

for sliding security doors

1.

Prepare Door

2.

Adjustable Rod Setup 

(OPTIONAL)

3.

Install Remote Locks

(PK0190) S14R Instructions A4 R13.cdr

Insert the 

rod free-ends

 into the two 

Ø5 drive holes 

on the rear of the centrelock.

Pull the 

free-ends

 of the 

rods 

out through the 

centrelock 

cutout. 

Insert the centrelock into the 

centrelock cutout

 and 

secure with two 

#8x13mm lock body screws.

 

rod
free-end

lock body
screw

PLEASE TURN PAGE FOR STEPS 6 - 11

4.

Remove Plug in Centrelock

Remove 

plug 

in the 

drive tab

 on the rear of the 

centrelock

 and discard.

 

Ø5mm 

REMOVE
Ø5mm plug

drive tab

5.

Install Centrelock

centrelock
cutout

Отзывы: