Kaba 5140 Series Скачать руководство пользователя страница 83

Страница: 83 / 86

Section 5 - 10

Assa Abloy

•

"YALE"

appears the latch face.

• All grade 1 & 2 product is key demountable.*

TOOLS:

• 5400 grade 1 knobs require a spanner wrench.

• 5400L grade 1 levers require an

" Allen wrench and an original Yale 5400L spanner wrench.

*The original 5400 Augusta Lever was non-key demountable.

This lock was pro duced for only a few months and was re de signed to be key demountable.

Division of Ingersoll Rand

•

"SCHLAGE"

appears the latch face.

TOOLS:

• Spanner wrench is required for grade 1.

• Castlenut bushing wrench (included with new locks) is required to install AL grade 2 leversets,

but not to change the cyl in ders.

•

" pin punch for depressing retainer

NOTES:

• Original S series tailpiece must be used in 5400-xx-1099 cylinder.

Schlage Lock Co.

Yale Security

Schlage D series

H series

A, AL series

S series

E/B series

grade 1

grade 2

tubular

knobs & levers interconnected knobs & levers

levers

deadlocks/latches

retrofit type KDH

KDH

Peaks Global: 5400-xx-1099

5400-xx-1099

Yale 5400L 5400

6200 Monolock 5300L

5300

grade 1

grade 1 unit lock

grade 2

levers

knobs

preassembled

levers

knobs

retrofit type KDH*

KDH

Peaks Global: 5400-xx-1055 5400-xx-1054

5400-xx-1054

5400-xx-1095 5400-xx-1054

Содержание 5140 Series























































































Результаты поиска

Содержание 5140 Series

Отзывы:

Похожие инструкции для 5140 Series

Бренды по названию

Популярные бренды

Kaba 5140 Series, Техническое руководство

Результаты поиска

Содержание 5140 Series

Отзывы:

Похожие инструкции для 5140 Series

Бренды по названию

Популярные бренды