Kaba 5140 Series Скачать руководство пользователя страница 76

Страница: 76 / 86

Section 5 - 3

lin

r I

lla

tio

Key demountable handle (KDH): Remove cylinder by turning any operating key, de press ing a retainer in the

shank of the handle, and pulling on the handle.

Most contemporary cylindrical locks have key demountable handles.

Non-key demountable handle (

Non-KDH

): Remove cylinder by disassembling the lockset.

Corbin Russwin and Sargent grade 1 knobs and preassembled locksets are the primary

Non-KDH

hardware.

brand

grade 1

grade 2

levers

knobs

preassembled

levers

knobs

Arrow

KDH

Corbin

KDH

Non-KDH

KDH

KDH/

Non-KDH

Russwin
Falcon

KDH

LSDA

KDH

Marks

KDH

PDQ

KDH

Sargent

KDH

Non-KDH

Non-KDH *

KDH

Schlage

KDH

Yale

KDH

1) Turn any operating key

to the right about 45 degrees.

2) Depress the re tain er through the

access hole in the trim, and pull off the knob.

NOTES:

*Sargent discontinued their unit lock decades ago. However, they also made a lock called the

"IntegraLock" (7600 Line) that used a small mortise body with through-bolted key-in-knob trim.

Cylinder Removal Methods

Содержание 5140 Series























































































Результаты поиска

Содержание 5140 Series

Отзывы:

Похожие инструкции для 5140 Series

Бренды по названию

Популярные бренды

Kaba 5140 Series, Техническое руководство

Результаты поиска

Содержание 5140 Series

Отзывы:

Похожие инструкции для 5140 Series

Бренды по названию

Популярные бренды