Kaba 5140 Series Скачать руководство пользователя страница 52

Страница: 52 / 86

Section 3 - 13

tti

&
P

Rekeying Conventional Cylinders

Pry off and discard the spring cover. Rekey and apply a new spring cover. Since all Peaks products are

designed to be top loaded, use of a follower for rekeying is optional.
Mortise / rim cylinder screws have a Loctite

coating. If cams or plug retainers are removed, use new

screws and tighten them firmly.

Pinning Conventional Cylinders

Pin to uniform pin stack height

Insert a key into the core and turn the plug 90 degrees. Extend the control lug into the locked position.

Top load the core. Let the bottom pins stop against the plug as shown in figure 1.
All the stacks should have a uniform height. Dump any incorrect chamber and repin it. When the pin

stack heights are uniform, turn the plug and let the pins drop into the plug.

5800 series capped small format interchangeable cores

Global cores come in .140" spacing only.

Place the core loaded with pins only, into the capping block.

Insert a tumbler spring, 3800-00-4010, into each chamber by

dropping them into the holes in the block.
One chamber at a time, place a cap on top of each spring

and tap it in place with the capping tool and a plastic or

rawhide mallet until the capping tool is flush against the block.

Do not use excessive force

Lubricate discs with Superlube™

synthetic grease.

For 140 cores, a capping press in .140" spacing is available from Kaba.

Rekeying

Place the ejector tool into the hole under the chamber(s) and drive out the pins,

spring, and cap with a light tap.

Discard the elements and repin. Always use new springs and caps.

1. Load pins

with plug turned.

3840-00-3540

140 capping block

(6 holes)

3800-00-3547

capping tool

is used with

both blocks

3800-00-3548

ejector tool

3. Errors in 4th and 5th chambers

Incorrect

2. Uniform pin stack heights

Correct

Pinning Interchangeable Cores

• Work on a firm bench surface.

• Strike tools gently with a plastic or rawhide mallet.

• Do not use a metal hammer.

Содержание 5140 Series























































































Результаты поиска

Содержание 5140 Series

Отзывы:

Похожие инструкции для 5140 Series

Бренды по названию

Популярные бренды

Kaba 5140 Series, Техническое руководство

Результаты поиска

Содержание 5140 Series

Отзывы:

Похожие инструкции для 5140 Series

Бренды по названию

Популярные бренды