Kaba 5140 Series Скачать руководство пользователя страница 68

Страница: 68 / 86

Section 4 - 5

&
R

The following key symbols are the lock industry standard, used by manufacturers, BHMA, DHI and ALOA.

They should be used when specifying any master keyed system. The symbols are constructed as follows:

Abbreviation Key type

Symbolized by

Symbols or "keysets"

GGMK

great grand master key

GGM

GGM

GMK

grand master key

single letter

A, B, C, T

master key

pair of letters

AA, AB, CC, BA, TR

change key

letters and numbers

AA1, AB29, 17AA, SKD1

One level of keying - the most secure keying

Locks are never master keyed, but keyed alike (KA) or keyed different (KD). If you have two cylinders keyed

to SKD1, it is a keyed alike group.

SKD1

SKD2

SKD3

SKD4

SKD5

SKD6

Two levels of keying - simple master key system

Consists of a Master and change keys. Master key is named with an identical pair of letters, AA, BB, CC, etc.

The change key numbers go

in front of

the letter pair.

1AA 2AA 3AA 4AA 5AA

SKD1

Three levels of keying - grand master key system

Consists of a Grand Master and multiple Master keys under the Grand. Change key numbers go

after

the

letter pair. The first letter of the master key symbols is the grand.

AA1 AA2 AA3

AB1 AB2 AB3

SKD1

SKD2

Four levels of keying - great grand master key system.

Consists of a Great Grand Master with multiple Grand Master "systems" under it. Change key numbers go

after

the letter pair.

GGM

AA1 AA2 AA3 AB1 AB2 AB3 BA1 BA2 BA3 BB1 BB2

SKD1

The Standard Key Coding System

Содержание 5140 Series























































































Результаты поиска

Содержание 5140 Series

Отзывы:

Похожие инструкции для 5140 Series

Бренды по названию

Популярные бренды

Kaba 5140 Series, Техническое руководство

Результаты поиска

Содержание 5140 Series

Отзывы:

Похожие инструкции для 5140 Series

Бренды по названию

Популярные бренды