manualshive.com logo in svg

K-Line CROP CADET SG60T, Инструкция по эксплуатации и безопасности

Поделиться
Скачать
K-Line CROP CADET SG60T Скачать руководство пользователя страница 19

19

SG60 SEEDER CROP CADET                                              OPERATOR & SAFETY MANUAL

S A F E T Y   S I G N   C A R E

•  Keep safety signs clean and legible at all times. 
•  Replace safety signs that are missing or have become illegible.
•  Replaced parts that displayed a safety sign should also display the current sign. 

TO ORDER SAFETY DECALS CONTACT:

USA:

 

K-Line 

Agriculture 

   

 

PO Box 248

             1023 W 9th St

             Grafton ND 58237 

             Email: 

[email protected]

             Free-call: 1800 445 6882

HOW TO INSTALL SAFETY SIGNS:

•  Be sure that the installation area is clean and dry.
•  Decide on the exact position before you remove the backing paper.
•  Remove the smallest portion of the split backing paper.
•  Align the decal over the specified area and carefully press the small portion with the exposed sticky 

backing in place.

•  Slowly peel back the remaining paper and carefully smooth the remaining portion of the decal in 

place.

•  Failure to comply could result in serious injury or death.

Australia:  

K-Line Agriculture

 

      PO Box 340

 

     74 Young Rd

 

     Cowra NSW 2794 

 

      Email: 

[email protected] 

 

      Free-call: 1800 194 131

Locate where necessary.

 

(Refer to safety decal placement, Pg 14) 

Figure 11

Содержание CROP CADET SG60T

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды