background image

16

3.  Gently lift and remove the SATA HDD or SSD 
4.  To install a HDD or SSD or other compatible SATA harddrive, reverse the steps and 

reinstall the PXI-63980 into the PXI system.

2.3.14    Replacing the Battery Backup

The PXI-63980 is provided with a 3.0 V “coin cell” lithium battery, replacement of which 

is as follows�

1.  Turn off the PXI chassis.
2.  Remove  the  PXI-63980  embedded  controller  from  the chassis. Observe all anti-

static precautions.

3.  To remove the battery, gently insert a small (approx. 5 mm) flathead screwdriver 

under the battery at the negative retaining clip. Gently pry up and the battery should 

easily pop out.

4.  Place a fresh identical battery (CR2032 or equivalent) in the socket, ensuring that the 

positive pole (+) is facing upwards. The battery is most easily seated by first being 

inserted  under  the  positive  retaining  clip,  and  then pushed downward at the 

negative retaining clip. The battery should easily snap into position.

5.  Reinstall the embedded controller into the PXI chassis and restore power.

2�3�15    Clearing CMOS

In the event of a system malfunction causing the PXI-63980 to halt or fail to boot, clear the 

CMOS and restore the controller BIOS to its default settings. To clear the CMOS:

1.  Shut down the controller operating system and turn off the PXI Chassis.
2.  Remove  the  PXI-63980  from  the  chassis.  Observe  all anti-static precautions.
3.  Locate  the  CMOS  clear  switch  (SW1)  on  the  board  (seeSection  2.3.10  Onboard 

Connections and Settings). Move the switch from Normal position

Содержание PXI-63980













































Отзывы: