23
Setting bass sound
7
Setting subwoofer output—SUBWOOFER OUT
You can select the type of the signal which can be transmitted
through the subwoofer. In other words, you can determine
whether or not the bass elements of the front speaker channels
are transmitted through the subwoofer regardless of the front
speaker size setting (either “SMALL” or “LARGE”).
SUBWFR OUT: LFE
Select to emit only the LFE signals (while playing Dolby
Digital and DTS software) or the bass elements of the
“SMALL” front speakers (while playing any source other than
above).
SUBWFR OUT: LFE+MAIN
Select to always emit the bass elements of the front speaker
channels (MAIN). While playing Dolby Digital and DTS
software, the bass elements and the LFE signals are both
emitted.
Initial setting:
SUBWFR OUT: LFE
NOTE
When “SUBWOOFER” is set to “SUBWOOFER: NO” (see page
21), this function is not available.
7
Setting the crossover frequency—CROSSOVER
Small speakers cannot reproduce the bass sounds efficiently. If
you use a small speaker in any position, this receiver
automatically reallocates the bass sound elements assigned to
the small speaker to the large speakers.
To use this function properly, set this crossover frequency level
according to the size of the small speaker connected.
• If you have selected “LARGE” for all speakers (see page 21),
this function will not take effect (“CROSSOVER: OFF” appears).
CROSSOVER: 80Hz
Select when the cone speaker unit built in
the speaker is about 12 cm.
CROSSOVER: 100Hz
Select when the cone speaker unit built in
the speaker is about 10 cm.
CROSSOVER: 120Hz
Select when the cone speaker unit built in
the speaker is about 8 cm.
CROSSOVER: 150Hz
Select when the cone speaker unit built in
the speaker is about 6 cm.
CROSSOVER: 200Hz
Select when the cone speaker unit built in
the speaker is less than 5 cm.
Initial setting:
CROSSOVER: 150Hz
NOTE
Crossover frequency is not valid for the HEADPHONE and 3D
HEADPHONE modes.
7
Setting the low frequency effect attenuator
—LFE ATT
If the bass sound is distorted while playing back software
encoded with
Dolby Digital
or
DTS
, set the LFE level to eliminate
distortion.
• This function takes effect only when the LFE signals come in.
LFE ATT: 0dB
Normally select this.
LFE ATT: –10dB
Select when the bass sound is distorted.
Initial setting:
LFE ATT: 0dB
Selecting the main or sub channel
—DUAL MONO
You can select the playback sound (channel) you want while
playing digital software recorded (or broadcasted) in Dual Mono
mode (see page 36), which includes two monaural channels
separately.
DUAL MONO: MAIN
Select to play back the main channel (Ch 1).*
Signal indicator “L” lights up while playing back this channel.
DUAL MONO: SUB
Select to play back the sub-channel (Ch 2).*
Signal indicator “R” lights up while playing back this channel.
DUAL MONO: ALL
Select to play back both the main and sub-channels (Ch 1/Ch 2).*
Signal indicators “L” and “R” light up while playing back these
channels.
Initial setting:
DUAL MONO: MAIN
* Dual Mono signals can be heard from the following speakers—L
(left front speaker), R (right front speaker), and C (center
speaker), with respect to the current Surround setting:
NOTE
The Dual Mono format is not identical with bilingual broadcasting
for TV programs. So this setting does not take effect while
watching such bilingual programs.
Dual Mono
setting
Ch 1
Ch 2
Ch 1
Ch 2
Ch 1
Ch 1
ALL
Ch 1
Ch 2
Ch 1+Ch 2
Ch 1+Ch 2 Ch 1+Ch 2
Ch1
Ch 2
Ch 2
Ch 2
L
R
L
R
C
L
R
MAIN
SUB
Without
Surround
With Surround Activated
Center speaker setting
SMALL/LARGE
NO
EN16-25RXF31S[A]1.p65
05.6.13, 10:36
23
